Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM3160E _59 Vehicle Exterior _019718 SLIDING ROOF / CONVERTIBLE _0106111 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  REASSEMBLY  


PROCEDURE

Hide 63205A 1.INSTALL SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

a.
B359429

Hold down the roof wind deflector panel sub-assembly.


b.

Using a screwdriver, slide the sliding roof drive cable sub-assembly as shown in the illustration to install it.

B359431
0.833,0.188 0.583,0.354 false 6.333,1.5 6.656,1.604 false 0.854,0.094 1.167,0.292 0.313,0.198 10 false *a 6.188,1.406 6.427,1.74 0.24,0.333 10 false *a
*a Protective Tape - -


HINT:

Tape the screwdriver tip before use.



c.

Insert the rear roof drip channel in the direction indicated by the arrow (1) in the illustration.

B359428
0.823,1.177 0.979,1.375 0.156,0.198 10 false 2 6.177,2.417 6.333,2.615 0.156,0.198 10 false 2 4.708,0.677 4.865,0.875 0.156,0.198 10 false 1


d.

Engage the 2 claws in the direction indicated by the arrow (2) in the illustration to install the rear roof drip channel.


Hide 2.ADJUST FULLY CLOSED POSITION

a.

Using a screwdriver, slide the sliding roof drive cable sub-assembly in either direction and align the alignment marks as shown in the illustration.

B359432
0.438,0.646 0.979,0.5 true 1.042,0.323 1.542,0.219 true 5.635,2.104 6.073,1.938 true 6.125,1.76 6.615,1.885 true 1.583,0.125 1.896,0.323 0.313,0.198 10 false *a 0.292,0.552 0.604,0.75 0.313,0.198 10 false *a 6.635,1.792 6.948,1.99 0.313,0.198 10 false *a 5.49,2.021 5.802,2.219 0.313,0.198 10 false *a
*a Alignment Mark - -


HINT:

Tape the screwdriver tip before use.



Hide 63306 3.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B359426

Insert the sunshade trim sub-assembly into the sliding roof housing sub-assembly.


b.

Engage the guide to install the sliding roof piece sub-assembly LH.

B359424

HINT:

Use the same procedure for the RH side.



c.

Install the 2 screws.


Hide 63260A 4.INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B359423

Install the sliding roof drive gear sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.
B359422
2.479,1.792 2.594,1.302 true 2.677,1.979 2.792,1.49 true 2.615,1.979 2.927,2.135 0.313,0.156 10 false *a 2.417,1.802 2.729,1.958 0.313,0.156 10 false *b
*a Guide
*b Pin


Engage the guide and pin.


c.

Engage the claw to install the map light bracket.