Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106116 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B203475
1.219,2.531 1.219,2.208 1.219,2.208 1.615,2.208 false 1.094,2.521 1.083,2.208 1.083,2.208 0.542,2.208 false 1.229,2.708 1.229,3.042 1.229,3.042 1.458,3.042 false 1.052,2.708 1.052,3.031 1.052,3.031 0.615,3.031 false 0.135,0.083 0.313,0.333 0.177,0.25 10 *a 1.646,2.146 1.969,2.365 0.323,0.219 10 GND 1.49,2.948 1.948,3.094 0.458,0.146 10 DOWN 0.365,2.948 0.604,3.177 0.24,0.229 10 UP 0.406,2.135 0.552,2.354 0.146,0.219 10 B 2.958,1.854 3.188,2.083 0.229,0.229 10 *b 2.333,2.333 2.542,2.542 0.208,0.208 10 *c
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise


Connect a positive (+) battery lead to terminal 2 (B).

NOTICE:

Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) battery lead to terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Battery Connection Specified Condition
1.

Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP) within 1 second.


Motor gear rotates clockwise
1.

Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery lead to terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


NOTICE:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.



Hide 85710E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B203474
2.417,2.5 2.417,2.188 2.417,2.188 2.833,2.188 false 2.302,2.5 2.302,2.188 2.302,2.188 1.781,2.188 false 2.271,2.708 2.271,3 2.271,3 1.823,3 false 2.438,2.698 2.438,3 2.438,3 2.677,3 false 0.063,0.063 0.281,0.26 0.219,0.198 10 *a 2.677,2.927 3.208,3.135 0.531,0.208 10 DOWN 2.854,2.104 3.208,2.333 0.354,0.229 10 GND 1.667,2.104 1.813,2.313 0.146,0.208 10 B 1.563,2.927 1.802,3.115 0.24,0.188 10 UP 0.302,1.813 0.5,1.99 0.198,0.177 10 *b 0.948,2.24 1.177,2.469 0.229,0.229 10 *c
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise


Connect a positive (+) battery lead to terminal 2 (B).

NOTICE:

Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) battery lead to terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Battery Connection Specified Condition
1.

Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP) within 1 second.


Motor gear rotates counterclockwise
1.

Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery lead to terminal 7 (DOWN) within 1 second.


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.