1.PERFORM SPARK TEST
Check for DTCs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If any DTCs are present, perform troubleshooting in accordance with the procedure for each DTC.
Remove the 4 ignition coil assemblies and 4 spark plugs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
If an ignition coil assembly or spark plug has been struck or dropped, replace it.
Arrange the removed parts in the correct order.
Disconnect the 4 fuel injector assembly connectors.
Install the spark plug into the ignition coil assembly, and then connect the ignition coil assembly connector.
Ground the spark plug.
Check that spark occurs at each spark plug while the engine is being cranked.
Be sure to ground the spark plugs when checking them.
Do not crank the engine for more than 2 seconds.
If a spark plug has been struck or dropped, replace it.
If an ignition coil assembly has been struck or dropped, replace it.
If spark does not occur, perform the following procedure.
Connect the 4 fuel injector assembly connectors.
Install the 4 spark plugs and 4 ignition coil assemblies.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
If a spark plug has been struck or dropped, replace it.
If an ignition coil assembly has been struck or dropped, replace it.
Install the same parts to their original positions.
Check for DTCs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
2.INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST
Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Check that the ignition coil assembly connector is securely connected.
| Result | Action |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil assembly.
Replace the ignition coil assembly with a known good one.
Perform the spark test again.
| Result | Action |
|---|---|
| NG | Go to next step |
| OK | Replace ignition coil assembly |
Perform a spark test on each spark plug.
Replace the spark plug with a known good one.
Connect the 4 fuel injector assembly connectors.
Install the 4 spark plugs and 4 ignition coil assemblies.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
If an ignition coil assembly has been struck or dropped, replace it.
If a spark plug has been struck or dropped, replace it.
Install the same parts to their original positions.
Check for DTCs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
19100P
3.INSPECT SPARK PLUG
Do not use a wire brush for cleaning.
Never attempt to adjust the electrode gap of a used spark plug.
Perform "Inspection After Repair" after replacing a spark plug.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| *a | Body Ground |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (terminal part) - Body ground | Always | 10 MΩ or higher |
If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method.
Start the engine.
Do not perform this step when any of the following DTCs are output: P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).
Quickly accelerate the engine to 4000 rpm 5 times.
Do not perform this step when any of the following DTCs are output: P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).
Remove the spark plug.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is any damage, replace the spark plug.
| Manufacturer | Spark Plug Type |
|---|---|
| DENSO | SK16HR11 |
| *a | Spark Plug Electrode Gap |
Check the spark plug electrode gap.
1.3 mm (0.0512 in.)
Never attempt to adjust the electrode gap of a used spark plug.
If the spark plug electrode gap is more than the maximum, replace the spark plug.
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Clean the spark plug.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6.0 kgf/cm2, 85 psi)
20 seconds or less
Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
Install the spark plug.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
4.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION