Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › THROTTLE BODY
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0106850 THROTTLE BODY A

1AR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A195071C02
2.063,1.458 0.51,1.958 0.51,1.958 1.49,0.917 true 0.302,1.896 0.49,2.115 0.188,0.219 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusions of the throttle body gasket oriented as shown in the illustration.


Hide 23881B 2.INSTALL FUEL HOSE BRACKET

a.

Install the fuel hose bracket to the throttle body with motor assembly with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 22030 3.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Install the throttle body with motor assembly to the intake manifold with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



b.

Connect the No. 1 water by-pass hose and No. 2 water by-pass hose to the throttle body with motor assembly and slide the 2 clips to secure them.


c.

Engage the fuel tube sub-assembly to the clamp.


d.

Connect the throttle body with motor assembly connector.


Hide 17705 4.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.

Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.


b.

Engage the 2 air cleaner cap clamps.


c.

Tighten the hose clamp.


d.

Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


e.

Connect the vacuum switching valve assembly to the No. 1 air cleaner hose and engage the hose clamp.


f.

Connect the mass air flow meter sub-assembly connector and engage the wire harness clamp.


Hide 12601B 5.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 8.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3 and clear the DTCs.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR


b.

Turn the ignition switch to ON without operating the accelerator pedal.


c.

Perform the "Inspection After Repair".

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


d.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




e.

Enter the following menus: Powertrain / Engine / Data List / Throttle Sensor Position.

Powertrain > Engine > Data List
Tester Display
Throttle Sensor Position
50003 234 12

f.

Fully depress the accelerator pedal and check that the value is 60% or higher.


g.

Perform a road test and confirm that there are no abnormalities.