Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0106946 REAR COMBINATION LIGHT ASSEMBLY G

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 81560 1.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

a.
E164477
1.49,1.073 1.927,1.292 0.438,0.219 1.865,2.063 2.427,2.063 false 1.865,1.719 2.333,1.458 false 1.865,2.375 2.385,2.604 false 0.958,2.052 1.521,2.052 false 0.219,0.188 0.49,0.365 0.271,0.177 10 false *a 2.49,1.99 2.813,2.167 0.323,0.177 10 false B 2.396,1.375 2.719,1.542 0.323,0.167 10 false STP 2.448,2.594 2.573,2.76 0.125,0.167 10 false E 0.75,1.99 0.969,2.167 0.219,0.177 10 false TL 1.594,1.104 1.917,1.271 0.323,0.167 10 false M30
*a Component without harness connected
(Rear Combination Light Assembly LH)


Disconnect the M30 rear combination light assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M30-2 (STP) - M30-6 (E) Brake pedal released Below 1 V
Brake pedal depressed 11 to 14 V
M30-4 (B) - M30-6 (E) Turn signal switch in neutral position Below 1 V
Ignition switch ON, turn signal switch in left turn position 11 to 14 V
(60 to 120 times per minute)
M30-3 (TL) - M30-6 (E) Light control switch off Below 1 V
Light control switch in tail position 11 to 14 V


If the result is not as specified, repair or replace wire harness or connector.


Hide 81550 2.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

a.
E164477
1.51,1.115 1.948,1.333 0.438,0.219 1.865,2.063 2.427,2.063 false 1.865,1.719 2.333,1.458 false 1.865,2.375 2.385,2.604 false 0.958,2.052 1.521,2.052 false 0.219,0.188 0.49,0.365 0.271,0.177 10 false *a 2.49,2 2.813,2.177 0.323,0.177 10 false B 2.396,1.375 2.719,1.542 0.323,0.167 10 false STP 2.448,2.594 2.573,2.76 0.125,0.167 10 false E 0.75,1.99 0.969,2.167 0.219,0.177 10 false TL 1.615,1.146 1.938,1.313 0.323,0.167 10 false M32
*a Component without harness connected
(Rear Combination Light Assembly RH)


Disconnect the M32 rear combination light assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M32-2 (STP) - M32-6 (E) Brake pedal released Below 1 V
Brake pedal depressed 11 to 14 V
M32-4 (B) - M32-6 (E) Turn signal switch in neutral position Below 1 V
Ignition switch ON, turn signal switch in right turn position 11 to 14 V
(60 to 120 times per minute)
M32-3 (TL) - M32-6 (E) Light control switch off Below 1 V
Light control switch in tail position 11 to 14 V


If the result is not as specified, repair or replace wire harness or connector.