Home › Vehicle Exterior › LIGHTING (EXT) › REAR LIGHT ASSEMBLY › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0106947 REAR LIGHT ASSEMBLY G

LIGHTING (EXT)  REAR LIGHT ASSEMBLY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 81590A 1.INSPECT REAR LIGHT ASSEMBLY LH

a.

Disconnect the X3 and X4 rear light assembly LH connectors.


b.
E288067
1.49,0.26 1.885,0.521 0.396,0.26 1.49,2.01 1.885,2.271 0.396,0.26 1.271,1.646 1.594,1.219 false 1.344,3.083 1.563,2.792 false 2.125,1.646 1.854,1.198 false 2.031,3.073 1.844,2.781 false 1.625,2.052 1.938,2.25 0.313,0.198 10 false X3 1.625,0.302 1.938,0.5 0.313,0.198 10 false X4 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.198,1.667 1.51,1.865 0.313,0.198 10 false E 2,3.094 2.313,3.292 0.313,0.198 10 false B 2.104,1.667 2.417,1.865 0.313,0.198 10 false B 1.271,3.094 1.583,3.292 0.313,0.198 10 false E
*a Component without harness connected
(Rear Light Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X3-1 (B) - X3-2 (E) Light control switch off Below 1 V
Light control switch in tail position 11 to 14 V
X4-1 (B) - X4-2 (E) Ignition switch ON, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V


If the result is not as specified, repair or replace wire harness or connector.


Hide 81580D 2.INSPECT REAR LIGHT ASSEMBLY RH

a.

Disconnect the X27 and X28 rear light assembly RH connectors.


b.
E288067
1.49,0.26 1.885,0.521 0.396,0.26 1.49,2.01 1.885,2.271 0.396,0.26 1.271,1.646 1.594,1.219 false 1.344,3.083 1.563,2.792 false 2.125,1.646 1.854,1.198 false 2.031,3.073 1.844,2.781 false 1.583,2.063 1.896,2.26 0.313,0.198 10 false X27 1.583,0.313 1.896,0.51 0.313,0.198 10 false X28 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.198,1.667 1.51,1.865 0.313,0.198 10 false E 2,3.094 2.313,3.292 0.313,0.198 10 false B 2.104,1.667 2.417,1.865 0.313,0.198 10 false B 1.271,3.094 1.583,3.292 0.313,0.198 10 false E
*a Component without harness connected
(Rear Light Assembly RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X27-1 (B) - X27-2 (E) Light control switch off Below 1 V
Light control switch in tail position 11 to 14 V
X28-1 (B) - X28-2 (E) Ignition switch ON, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V


If the result is not as specified, repair or replace wire harness or connector.