Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the power seat switch, and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B345464E05
4.927,0.521 5.292,0.698 0.365,0.177 10 false +B 4.917,1.063 5.281,1.24 0.365,0.177 10 false IG 4.917,1.552 5.354,1.729 0.438,0.177 10 false GND 4.208,0.521 4.573,0.698 0.365,0.177 10 false d6 4.563,1.052 4.927,1.229 0.365,0.177 10 false e7 4.573,1.552 4.938,1.729 0.365,0.177 10 false e6 4.635,2.063 6.208,2.448 1.573,0.385 10 false Position Control ECU and Switch Assembly 4.219,1.052 4.583,1.229 0.365,0.177 10 false d7 4.573,0.51 4.938,0.688 0.365,0.177 10 false e6 4.552,0.333 4.917,0.51 0.365,0.177 10 false 7*1 4.177,0.854 4.542,1.031 0.365,0.177 10 false 3*2 4.542,1.344 4.906,1.521 0.365,0.177 10 false 2*1 4.188,1.344 4.552,1.521 0.365,0.177 10 false 2*2 4.177,0.333 4.542,0.51 0.365,0.177 10 false 7*2 4.531,0.854 4.896,1.031 0.365,0.177 10 false 3*1 4.208,1.542 4.573,1.719 0.365,0.177 10 false d6 2.583,1.198 3.521,1.396 0.938,0.198 10 false IG1 NO.3 0.906,0.5 2.083,0.708 1.177,0.208 10 false from Battery 0.448,1.042 2.219,1.26 1.771,0.219 10 false from IG1 NO.3 Relay 2.438,0.688 3.396,1.052 0.958,0.365 10 false P/SEAT F/L*1, P/SEAT F/R*2 0.219,2.156 1.208,2.333 0.99,0.177 10 false *1: for LHD 0.208,2.438 1.198,2.615 0.99,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
All power seat functions do not operate A
One or more power seat functions do not operate B




A

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SUPPLY)

B

GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate)

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SUPPLY)
a.

Disconnect the e6 and e7*1 or d6 and d7*2 position control ECU and switch assembly connectors.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e6-7 (+B) - Body ground Always 11 to 14 V
e7-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


for RHD
Tester Connection Condition Specified Condition
d6-7 (+B) - Body ground Always 11 to 14 V
d7-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e6-2 (GND) - Body ground Always Below 1 Ω


for RHD
Tester Connection Condition Specified Condition
d6-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR