Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag sensor assembly and seat belt buckle switch LH (front seat inner belt assembly LH).

DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch LH circuit.

·

Seat belt buckle switch LH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 Floor wire

·

Seat belt buckle switch LH (Front seat inner belt assembly LH)

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C239223E13
1.667,0.76 2.375,1.365 0.708,0.604 10 false LBE+ 1.688,2.198 2.365,2.677 0.677,0.479 10 false LBE- 5.406,0.896 5.833,1.333 0.427,0.438 10 false LBE+ 5.406,2.073 5.865,2.5 0.458,0.427 10 false LBE- 2.115,0.802 2.479,1.26 0.365,0.458 10 false 2 2.115,1.958 2.448,2.375 0.333,0.417 10 false 1 5.135,0.802 5.51,1.333 0.375,0.531 10 false 10 5.135,1.958 5.448,2.365 0.313,0.406 10 false 18 0.552,2.917 1.365,3.302 0.813,0.385 10 false M4 0.552,3.073 2.688,3.625 2.135,0.552 10 false Seat Belt Buckle Switch LH (Front Seat Inner Belt Assembly LH) 5.323,2.917 5.74,3.354 0.417,0.438 10 false M7 5.323,3.073 6.896,3.479 1.573,0.406 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

2.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C265017C02
0.344,3.635 0.677,3.875 0.333,0.24 1.135,0.531 1.469,0.771 0.333,0.24 0.906,4.24 1.281,3.771 false 1.896,4.25 1.521,3.781 false 1.531,2.094 1.531,1.677 1.531,1.677 1.365,1.677 false 2.073,0.802 1.823,0.802 false 2,0.333 2.375,0.677 false 2,1.25 2.375,0.906 false 0.583,2.052 0.938,2.396 0.354,0.344 10 false *1 2.521,2.396 2.854,2.708 0.333,0.313 10 false *2 1.208,1.604 1.594,1.948 0.385,0.344 10 false *3 1.677,0.729 2.021,1.031 0.344,0.302 10 false *4 0.938,0.146 1.292,0.49 0.354,0.344 10 false *a 0.198,3.167 0.521,3.5 0.323,0.333 10 false *b 2.021,2.083 2.354,2.396 0.333,0.313 10 false A 1.729,2.083 2.063,2.396 0.333,0.313 10 false B 1.271,2.083 1.604,2.396 0.333,0.313 10 false C 0.969,2.083 1.302,2.396 0.333,0.313 10 false D 1.208,0.563 1.542,0.875 0.333,0.313 10 false M7 0.417,3.677 0.75,3.99 0.333,0.313 10 false M4 1.615,0.25 2.042,0.458 0.427,0.208 10 false LBE+ 1.625,1.188 2.052,1.396 0.427,0.208 10 false LBE- 1.771,4.25 2.302,4.5 0.531,0.25 10 false LBE+ 0.76,4.25 1.167,4.479 0.406,0.229 10 false LBE-
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (LBE+) - M4-1 (LBE-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C265018C01
0.542,2.417 0.896,2.667 0.354,0.25 1.531,0.688 1.531,0.271 1.531,0.271 1.698,0.271 false 0.906,2.99 1.354,2.531 false 2.063,3 1.604,2.542 false 0.604,0.667 1.021,1.021 0.417,0.354 10 false *1 2.49,0.99 2.865,1.438 0.375,0.448 10 false *2 1.729,0.188 2.042,0.344 0.313,0.156 10 false *3 0.375,1.875 0.781,2.25 0.406,0.375 10 false *a 0.75,3 1.25,3.333 0.5,0.333 10 false LBE- 1.938,3 2.438,3.333 0.5,0.333 10 false LBE+ 0.625,2.458 1.125,2.792 0.5,0.333 10 false M4 2.01,0.677 2.385,1.125 0.375,0.448 10 false A 1.719,0.677 2.094,1.125 0.375,0.448 10 false B 1.271,0.677 1.646,1.125 0.375,0.448 10 false C 0.979,0.677 1.354,1.125 0.375,0.448 10 false D
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (LBE+) - M4-1 (LBE-) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

4.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C265018C01
0.542,2.417 0.896,2.667 0.354,0.25 1.531,0.688 1.531,0.271 1.531,0.271 1.698,0.271 false 0.906,2.99 1.354,2.531 false 2.063,3 1.604,2.542 false 0.604,0.667 1.021,1.021 0.417,0.354 10 false *1 2.49,0.99 2.865,1.438 0.375,0.448 10 false *2 1.729,0.188 2.042,0.344 0.313,0.156 10 false *3 0.375,1.875 0.781,2.25 0.406,0.375 10 false *a 0.75,3 1.25,3.333 0.5,0.333 10 false LBE- 1.938,3 2.438,3.333 0.5,0.333 10 false LBE+ 0.625,2.458 1.125,2.792 0.5,0.333 10 false M4 2.01,0.677 2.385,1.125 0.375,0.448 10 false A 1.719,0.677 2.094,1.125 0.375,0.448 10 false B 1.271,0.677 1.646,1.125 0.375,0.448 10 false C 0.979,0.677 1.354,1.125 0.375,0.448 10 false D
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-2 (LBE+) - Body ground Ignition switch ON Below 1 V
M4-1 (LBE-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C265018C01
0.542,2.417 0.896,2.667 0.354,0.25 1.531,0.688 1.531,0.271 1.531,0.271 1.698,0.271 false 0.906,2.99 1.354,2.531 false 2.063,3 1.604,2.542 false 0.604,0.667 1.021,1.021 0.417,0.354 10 false *1 2.49,0.99 2.865,1.438 0.375,0.448 10 false *2 1.729,0.188 2.042,0.344 0.313,0.156 10 false *3 0.375,1.875 0.781,2.25 0.406,0.375 10 false *a 0.75,3 1.25,3.333 0.5,0.333 10 false LBE- 1.938,3 2.438,3.333 0.5,0.333 10 false LBE+ 0.625,2.458 1.125,2.792 0.5,0.333 10 false M4 2.01,0.677 2.385,1.125 0.375,0.448 10 false A 1.719,0.677 2.094,1.125 0.375,0.448 10 false B 1.271,0.677 1.646,1.125 0.375,0.448 10 false C 0.979,0.677 1.354,1.125 0.375,0.448 10 false D
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (LBE+) - Body ground Always 1 MΩ or higher
M4-1 (LBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK DTC
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the front seat inner belt assembly LH with a known good one.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the front seat inner belt assembly LH that was installed for testing to its original location.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL


Result:
Proceed to
OK
NG



OK

NG