Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.12–2014.08
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0107329 AUTOMATIC TRANSAXLE UNIT G

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35394 1.INSPECT TRANSMISSION OIL CLEANER MAGNET

a.
C138722

Use the removed transmission oil cleaner magnets to collect any steel chips. Examine the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to determine what type of wear has occurred in the automatic transaxle assembly:

Result:
Steel (magnetic):

Bearing, gear and plate wear

Brass (non-magnetic):

Bushing wear



Hide 2.INSPECT INPUT SHAFT SUB-ASSEMBLY END PLAY

a.
C136696

Using a dial indicator, measure the input shaft sub-assembly end play.

End Play:

0.012 to 1.250 mm (0.000473 to 0.0492 in.)



Hide 3.INSPECT NO. 2 CLUTCH DISC

a.
C138267

Check if the contact surfaces of the No. 2 clutch discs, No. 2 clutch plates and No. 2 clutch flange are worn or burnt.

NOTICE:
·

If the lining of any No. 2 clutch disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 2 clutch discs.

·

Before assembling new No. 2 clutch discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 35706V 4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C138259

Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear sub-assembly.

Standard Inside Diameter:

25.525 to 25.546 mm (1.0049 to 1.0057 in.)


Maximum Inside Diameter:

25.546 mm (1.0057 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.


Hide 5.INSPECT NO. 1 CLUTCH DISC

a.
C138265

Check if the contact surfaces of the No. 1 clutch discs, No. 1 clutch plates and No. 1 clutch flange are worn or burnt.

NOTICE:
·

If the lining of any No. 1 clutch disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 1 clutch discs.

·

Before assembling new No. 1 clutch discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 35683B 6.INSPECT NO. 3 BRAKE DISC

a.
C138255

Check if the contact surfaces of the No. 3 brake discs, No. 3 brake plates and No. 3 brake flanges are worn or burnt.

NOTICE:
·

If the lining of any No. 3 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 3 brake discs.

·

Before assembling new No. 3 brake discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 34330 7.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C291374

Using a feeler gauge, measure the clearance between the underdrive planetary gear assembly and the pinion gear at 4 points.

Standard Clearance:

0.18 to 0.54 mm (0.00709 to 0.0213 in.)


If the clearance is greater than the standard clearance, replace the underdrive planetary gear assembly.


Hide 35730 8.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

a.
C138266

Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear assembly.

Standard Inside Diameter:

25.580 to 25.601 mm (1.0071 to 1.0079 in.)


Maximum Inside Diameter:

25.601 mm (1.0079 in.)


If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.


Hide 9.INSPECT NO. 1 BRAKE DISC

a.
C138255

Check if the contact surfaces of the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are worn or burnt.

NOTICE:
·

If the lining of any NO. 1 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all NO. 1 brake discs.

·

Before assembling new NO. 1 brake discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 35608L 10.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C138254

Using a vernier caliper, measure the free length of the 3 2nd brake piston return spring sub-assemblies including the spring seats.

Standard Free Length:

23.85 mm (0.939 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 35790 11.INSPECT ONE-WAY CLUTCH ASSEMBLY

a.
C189425C06
2.573,1.01 2.25,1.01 false 1.031,1.083 0.615,1.083 false 2.396,0.302 2.583,0.469 0.188,0.167 10 false *b 0.563,0.302 0.75,0.458 0.188,0.156 10 false *a 2.615,0.927 2.792,1.094 0.177,0.167 10 false *2 0.417,0.99 0.583,1.146 0.167,0.156 10 false *1
*1 Planetary Ring Gear
*2 One-way Clutch Assembly
*a Free
*b Lock


Temporarily install the one-way clutch assembly to the planetary ring gear.


b.

Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the one-way clutch assembly does not operate normally, replace it.


Hide 35720 12.INSPECT FRONT PLANETARY GEAR ASSEMBLY

a.
C137433N02
1.503,0.257 1.65,0.423 0.147,0.166 10 A 2.07,3.363 2.217,3.528 0.147,0.166 10 B

Using a feeler gauge, measure the clearance between the front planetary gear case and each pinion gear at points A and B.

Standard Clearance:
Point A:

0.23 to 0.59 mm (0.00906 to 0.0232 in.)

Point B:

0.16 to 0.66 mm (0.00630 to 0.0259 in.)


If the clearance is greater than the standard clearance, replace the front planetary gear assembly.


Hide 35682A 13.INSPECT NO. 2 BRAKE DISC

a.
C137438

Check if the contact surfaces of the No. 2 brake discs, No. 2 brake plates and No. 2 brake flange are worn or burnt.

NOTICE:
·

If the lining of any No. 2 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 2 brake discs.

·

Before assembling new No. 2 brake discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 35068C 14.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C141533

a.

Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly including the spring seat.

Standard Free Length:

15.79 mm (0.622 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 35682A 15.INSPECT CLEARANCE OF NO. 2 BRAKE

a.
C137439

Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.884 to 1.196 mm (0.0348 to 0.0471 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

HINT:

There are 5 No. 2 brake flanges of different thicknesses.


No. 2 Brake Flange Thickness: mm (in.)
Mark Thickness
40 4.0 (0.157)
41 4.1 (0.161)
42 4.2 (0.165)
43 4.3 (0.169)
44 4.4 (0.173)


Hide 35691A 16.INSPECT CLEARANCE OF NO. 1 BRAKE

a.
C138258

Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.807 to 0.974 mm (0.0318 to 0.0383 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

HINT:

There are 6 No. 1 brake flanges of different thicknesses.


No. 1 Brake Flange Thickness: mm (in.)
Mark Thickness
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)


Hide 35683B 17.INSPECT CLEARANCE OF NO. 3 BRAKE

a.
C138724
2.01,0.802 2.229,0.438 2.229,0.438 2.396,0.438 false 2.292,3.677 1.844,3.146 1.844,3.146 1.688,3.146 false 3.229,3.719 3.042,3.719 false 1.198,0.375 1.375,0.563 0.177,0.188 10 false *a 2.594,3.271 2.76,3.438 0.167,0.167 10 false *b 1.51,3.063 2,3.354 0.49,0.292 10 false *2 2.458,0.375 2.885,0.635 0.427,0.26 10 false *1 3.26,3.656 3.427,3.802 0.167,0.146 8 false *c
*1 Front Oil Pump Assembly
*2 No. 3 Brake Piston
*a Dimension A
*b Dimension B
*c Contact surface of front oil pump assembly


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.

HINT:

Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.



b.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).

HINT:

Measure dimension B at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.



c.

Calculate the clearance value using the following formula:

Clearance = Dimension B - Dimension A

Standard Clearance:

0.599 to 0.761 mm (0.0236 to 0.0300 in.)


If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.

HINT:

There are 6 No. 3 brake flanges of different thicknesses.


No. 3 Brake Flange Thickness: mm (in.)
Mark Thickness
38 3.80 (0.150)
39 3.90 (0.154)
40 4.00 (0.157)
41 4.10 (0.161)
42 4.20 (0.165)
43 4.30 (0.169)


Hide 18.INSPECT CLEARANCE OF NO. 1 CLUTCH DISC

a.
C138728

Install the direct multiple disc clutch assembly to the rear transaxle cover sub-assembly.


b.

Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the No. 1 clutch flange diameter is approximately 152 mm (5.98 in.) and calculate the average.


Pack Clearance:

0.806 to 0.974 mm (0.0317 to 0.0383 in.)


If the pack clearance is not as specified, select an appropriate No. 1 clutch flange so that the pack clearance will be within the specified range.

HINT:

There are 6 No. 1 clutch flanges of different thicknesses.


No. 1 Clutch Flange Thickness: mm (in.)
Mark Thickness
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)


Hide 19.INSPECT CLEARANCE OF NO. 2 CLUTCH DISC

a.
C138727

Install the direct multiple disc clutch assembly to the rear transaxle cover sub-assembly.


b.

Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.


Pack Clearance:

0.544 to 0.744 mm (0.0214 to 0.0293 in.)


If the pack clearance is not as specified, select an appropriate No. 2 clutch flange so that the pack clearance will be within the specified range.

HINT:

There are 6 No. 2 clutch flanges of different thicknesses.


No. 2 Clutch Flange Thickness: mm (in.)
Mark Thickness
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)