33550
1.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/o Smart Entry and Start System)
If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.
Inspect wire harness:
Disconnect the shift lock control ECU connector.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 4 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 8 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
|---|---|---|
| 1 (E) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
Inspect key interlock solenoid operation signal:
Connect the shift lock control ECU connector.
| *a | Component with harness connected
(Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| Ignition switch ACC and shift lever not in P | 11 to 14 V |
Do not disconnect the shift lock control ECU connector.
If the result is not as specified, repair or replace the transmission floor shift assembly.
Inspect shift lock solenoid:
Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.
Disconnect the shift lock solenoid connector.
| *a | Front view of wire harness connector
(to Shift Lock Solenoid) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω |
If the result is not as specified, replace the transmission floor shift assembly.
If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
If the result is not as specified, replace the transmission floor shift assembly.
If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.
33550
2.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/ Smart Entry and Start System)
If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.
Inspect wire harness:
Disconnect the shift lock control ECU connector.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 12 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
|---|---|---|
| 3 (E) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
Inspect shift lock solenoid:
Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.
Disconnect the shift lock solenoid connector.
| *a | Front view of wire harness connector
(to Shift Lock Solenoid) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω |
If the result is not as specified, replace the transmission floor shift assembly.
If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
If the result is not as specified, replace the transmission floor shift assembly.
If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.
3.INSPECT TRANSMISSION CONTROL SWITCH
Disconnect the transmission control switch connector.
| *a | Component without harness connected
(Transmission Control Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IG) - 7 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| Shift lever not in S, "+" or "-" | 10 kΩ or higher | |
| 2 (SFTU) - 5 (E) | Shift lever held in "+" | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| 1 (SFTD) - 5 (E) | Shift lever held in "-" | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
If the result is not as specified, replace the transmission floor shift assembly.