Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.12–2014.08
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107351 DIFFERENTIAL CASE A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331Q 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C301118C01
0.875,0.167 1,0.167 1,0.167 1.167,0.354 false 0.469,1.542 0.729,1.542 false 0.583,1.125 0.708,1.125 0.708,1.125 0.875,1.313 false 1.448,1.646 1.708,1.646 false 1.448,1.938 1.708,1.938 false 1.365,0.698 1.677,0.188 1.677,0.188 1.802,0.188 false 1.771,0.802 1.906,0.563 1.906,0.563 2.031,0.563 false 1.656,1.052 1.823,1.323 1.823,1.323 1.938,1.323 false 2,1.24 2.365,1.49 0.365,0.25 10 false *1 0.302,1.448 0.667,1.708 0.365,0.26 10 false *2 1.844,0.094 2.188,0.375 0.344,0.281 10 false *3 0.708,0.073 1.021,0.323 0.313,0.25 10 false *4 1.75,1.865 2.125,2.177 0.375,0.313 10 false *4 0.406,1.042 0.76,1.25 0.354,0.208 10 false *1 1.76,1.573 2.104,1.854 0.344,0.281 10 false *3 2.063,0.49 2.427,0.75 0.365,0.26 10 false *2
*1 Front Differential Pinion
*2 Front Differential Pinion Thrust Washer
*3 Differential Side Gear
*4 Front No. 1 Differential Side Gear Thrust Washer


Coat the 2 differential side gears, 2 front No. 1 differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C196815

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C196825

Using a 3 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the differential case.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C196826

Using a chisel and a hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C138712N02
1.75,0.771 2.302,0.615 2.302,0.615 1.865,0.917 false 2.365,0.542 2.906,0.792 0.542,0.25 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing cage when installing the front differential case rear tapered roller bearing.

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing and differential case.




b.
C196828N03
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case sub-assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing outer race and transaxle case.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C196921N02
1.104,0.531 0.854,0.49 0.854,0.49 0.979,0.885 false 0.854,0.49 1.021,0.719 false 0.5,0.375 0.813,0.531 0.313,0.156 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing cage when installing the front differential case front tapered roller bearing.

·

Ensure that there is no clearance between the front differential case front tapered roller bearing and differential case.




b.

Install the shim to the transaxle housing.


c.
C196830N03
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing outer race, shim and transaxle housing.



Hide 7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C287785

Install the differential case to the transaxle case sub-assembly.


c.
C196800N01
0.875,0.74 0.573,0.208 0.573,0.208 1.333,0.469 false 0.583,0.208 1.146,0.531 false 1.771,0.5 2.979,0.281 2.979,0.281 2.292,0.74 false 2.49,1.417 3.135,1.052 3.135,1.052 2.573,0.927 false 0.677,1.625 0.219,1.292 0.219,1.292 0.594,1.021 false 0.573,0.208 1.021,0.635 false 2.021,0.615 2.948,0.292 false 1.094,1.813 1.021,2.01 false 2.604,1.156 3.104,1.052 false 1.5,1.625 2.646,2 2.646,2 2.229,1.646 false 1.896,1.656 2.615,1.979 false 0.24,1.292 0.552,1.375 false 0.24,1.281 0.542,1.198 false 1.302,1.74 1.031,2.01 1.031,2.01 0.875,1.76 false 0.406,0.104 0.563,0.302 0.156,0.198 10 false A 0.052,1.208 0.208,1.406 0.156,0.198 10 false A 0.865,1.958 1.031,2.135 0.167,0.177 10 false A 3.052,0.177 3.208,0.375 0.156,0.198 10 false A 3.188,0.969 3.344,1.167 0.156,0.198 10 false A 2.698,1.927 2.854,2.125 0.156,0.198 10 false B

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)
Bolt (B) : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)


d.
C301120N01
0.531,4.156 0.667,4.156 0.667,4.156 1.063,3.396 false 0.219,4.073 0.719,4.302 0.5,0.229 10 false SST

Using SST, turn the differential case right and left 2 or 3 times to settle the bearings.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

0.8 to 1.4 N*m (9 to 14 kgf*cm, 8 to 12 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.105)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.106)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.107)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.108)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.100) 2.775 (0.109)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.101) 2.800 (0.110)
2.150 (0.0846) 2.375 (0.0935) 2.600 (0.102) 2.825 (0.111)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.103) 2.850 (0.112)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.104) 2.875 (0.113)


f.
C296577

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C287785

Remove the differential case from the transaxle case assembly.


Hide 41221 8.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the front differential case.


c.
C196807C03
1.25,1.469 0.573,1.229 0.573,1.229 1.188,1.521 true 0.375,1.146 0.563,1.323 0.188,0.177 10 *a
*a Matchmark


Align the matchmarks, and install the front differential ring gear to the differential case quickly.

NOTICE:

Do not install the bolts while the front differential ring gear is hot.



d.
C301117

Install and tighten the 12 bolts.

Torque:
120 N*m (1223 kgf*cm, 88 ft.*lbf)

NOTICE:

Tighten the bolts a little at a time in a diagonal sequence.



Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.
C196831N02
1.427,1.313 0.635,2.333 0.635,2.333 1.375,1.542 false 2.156,1.865 2.615,1.865 2.615,1.865 2.542,2.083 false 0.271,2.281 0.583,2.448 0.313,0.167 10 true SST 2.698,1.802 3.167,2.063 0.469,0.26 10 false SST

Using SST and a hammer, install the front drive shaft oil seal LH to the transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front drive shaft oil seal LH is installed in the correct direction.



Hide 43410M 10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Inside:

i.

Coat the lip of a new front drive shaft case oil seal RH with MP grease.


ii.
C301121N01
2.5,0.688 2.802,0.5 2.802,0.5 2.625,1.031 false 2.844,0.385 3.26,0.615 0.417,0.229 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the differential case.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)




b.

Outside:

i.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


ii.
C188861N03
1.198,1.906 1.125,2.333 1.125,2.333 0.906,2.104 false 1.042,2.375 1.396,2.563 0.354,0.188 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:

Check that the front drive shaft oil seal RH is installed in the correct direction.