Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0107984 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C207073

Remove the cotter pin and nut.


c.
C165932C02
0.844,2.688 2.031,2.688 2.031,2.688 2.031,2.573 false 1.854,2.688 1.854,2.573 false 0.938,0.281 1.719,0.281 1.719,0.281 1.719,1.01 false 1.573,1.042 1.573,0.281 false 0.552,2.615 0.865,2.771 0.313,0.156 10 false SST 0.635,0.208 0.948,0.365 0.313,0.156 10 false SST 2.042,2.938 2.354,3.094 0.313,0.156 10 false *a
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050, 09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



d.
C289806C02
2.427,1.698 2.229,1.698 2.229,1.698 2.042,1.354 true 0.469,2.188 0.885,2.188 false 1.156,4.177 1.323,4.177 1.323,4.177 1.448,3.969 false 2.333,0.385 2.646,0.542 0.313,0.156 10 false *a 2.479,1.615 2.792,1.771 0.313,0.156 10 false *b 1.01,4.104 1.323,4.26 0.313,0.156 10 false *c 2.302,0.74 2.615,0.896 0.313,0.156 10 false *a 2.292,3.438 2.604,3.594 0.313,0.156 10 false A 2.292,3.729 2.604,3.885 0.313,0.156 10 false B 0.188,2.115 0.552,2.271 0.365,0.156 10 false SST
*a Molybdenum grease application area
*b Place wrench here
*c Center Nut


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part indicated in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.