Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FE) › 2013.12–2016.11
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0107994 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FE)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

a.

Install a new front drive shaft hole snap ring.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.



Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.
C296172C01
0,0 0,0 false
V100144

ATF WS


Apply ATF WS to the area shown in the illustration.


b.
C292485

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



c.
C293511C01
2.656,0.542 2.99,0.542 2.99,0.542 2.99,1.667 false 2.802,0.865 2.99,0.865 false 2.927,1.677 3.24,1.875 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.

NOTICE:
·

Do not push the front axle assembly further out of the vehicle than is necessary.

·

Be careful not to damage the front axle outboard joint boot.

·

Check for any foreign matter on the speed sensor rotor and insertion part.

·

Do not damage the speed sensor rotor.




Hide 43410 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

for 2WD:

i.
C296173C01
0,0 0,0 false
V100144

ATF WS


Apply ATF WS to the area shown in the illustration.


ii.

Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.


iii.

Install the front drive shaft assembly RH.

NOTICE:
·

Do not damage the front drive shaft oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

When inserting the front drive shaft assembly RH, keep it level.




iv.
C292483

Install the bearing bracket hole snap ring and a new No. 1 drive shaft bearing bracket setting bolt.

Torque:
32.4 N*m (330 kgf*cm, 24 ft.*lbf)



b.

for AWD:

i.
C296174C01
0,0 0,0 false
V100144

Toyota genuine differential gear oil LT


Apply Toyota genuine differential gear oil LT to the area shown in the illustration.


ii.

Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.


iii.

Install the front drive shaft assembly RH.

NOTICE:
·

Do not damage the transfer case oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

When inserting the front drive shaft assembly RH, keep it level.




iv.
C292484

Install the bearing bracket hole snap ring and a new No. 1 drive shaft bearing bracket setting bolt.

Torque:
32.4 N*m (330 kgf*cm, 24 ft.*lbf)



c.
C294860C01
0.427,1.552 0.427,0.542 0.427,0.542 0.781,0.542 false 0.438,0.854 0.625,0.854 false 0.354,1.563 0.667,1.76 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.

NOTICE:
·

Do not push the front axle assembly further out of the vehicle than is necessary.

·

Be careful not to damage the front axle outboard joint boot.

·

Check for any foreign matter on the speed sensor rotor and insertion part.

·

Do not damage the speed sensor rotor.




Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 48810 5.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 89543 7.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C291653C01
2.51,1.792 2.51,1.531 true 2.438,1.792 2.594,1.958 0.156,0.167 10 true *a
*a Sensor Clamp


Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor and front flexible hose when installing them.


HINT:

Install the front speed sensor harness bracket first and then the front flexible hose.



c.

Engage the 2 claws to install the sensor clamp.


Hide 43502H 8.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C293512

Using a 30 mm socket wrench, install the front axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)

HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 10.ADD TRANSFER OIL (for AWD)

Hide 11.INSPECT TRANSFER OIL LEAK (for AWD)

Hide 12.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 13.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT