Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY(for AWD)
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0107995 REAR DRIVE SHAFT ASSEMBLY(for AWD) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for AWD)  DISASSEMBLY  


PROCEDURE

Hide 42346B 1.SEPARATE REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C294166C01
0.448,3.24 0.938,3.781 0.938,3.781 1.323,3.313 false 0.073,0.052 0.385,0.208 0.313,0.156 10 false *A 0.094,2.365 0.406,2.521 0.313,0.156 10 false *B 0.885,3.802 1.198,3.958 0.313,0.156 10 false *a
*A for Type A
*B for Type B
*a Claw


Using needle-nose pliers, separate the rear No. 2 drive shaft inboard joint boot clamp (for Type A).


c.

Using needle-nose pliers, disengage the 2 claws as shown in the illustration and separate the rear No. 2 drive shaft inboard joint boot clamp (for Type B).


Hide 42346A 2.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the rear No. 2 drive shaft inboard joint boot clamp.


Hide 3.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Separate the rear drive shaft inboard joint boot from the rear drive shaft inboard joint assembly.


Hide 4.REMOVE REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the rear drive shaft inboard joint assembly.


b.
C166352C01
1.583,1.146 1.594,0.458 true 1.938,0.698 1.938,0.448 1.938,0.448 1.146,0.448 false 0.969,0.365 1.281,0.563 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the rear drive shaft inboard joint assembly and rear drive shaft outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the rear drive shaft inboard joint assembly from the rear drive shaft outboard joint shaft assembly.


d.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C160822

Using a snap ring expander, remove the shaft snap ring from the rear drive shaft outboard joint shaft assembly.


f.
C162724
2.906,0.531 1.521,0.313 1.521,0.313 3,0.615 false 1.344,0.24 1.542,0.406 0.198,0.167 10 *a
*a Matchmark


Put matchmarks on the rear drive shaft outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the rear drive shaft outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 5.REMOVE REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Remove the rear No. 2 drive shaft inboard joint boot clamp, rear drive shaft inboard joint boot and rear drive shaft inboard joint boot clamp.


Hide 42346B 6.SEPARATE REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.
C277140

Using a screwdriver, separate the rear No. 2 drive shaft outboard joint boot clamp as shown in the illustration.


Hide 42346A 7.SEPARATE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.
C277139

Using pliers, separate the rear drive shaft outboard joint boot clamp as shown in the illustration.


Hide 8.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Remove the rear drive shaft outboard joint boot clamp, rear drive shaft outboard joint boot and rear No. 2 drive shaft outboard joint boot clamp from the rear drive shaft outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.


Hide 9.REMOVE REAR DRIVE SHAFT DUST COVER

a.
F040647N02
1.927,0.813 2.313,0.354 2.313,0.354 2.542,0.354 false 2.583,0.292 2.979,0.521 0.396,0.229 10 false SST

Using SST and a press, remove the rear drive shaft dust cover.

SST
09950-00020  

NOTICE:
·

Do not drop the rear drive shaft inboard joint assembly.

·

Do not overtighten SST.