Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0101296 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 85012A 2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY

a.

Turn the ignition switch to ON.


b.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


c.

Turn the ignition switch off.


d.

Temporarily install the front wiper crank sub-assembly to the windshield wiper motor assembly with the nut.


e.

Temporarily install the windshield wiper link No. 1 rod to the pivot of the front wiper crank sub-assembly.


f.

Align the nut and pivot of the front wiper crank sub-assembly with the windshield wiper link No. 1 rod as shown in the illustration.

E288191
4.792,2.052 4.604,1.542 true 3.052,2.156 2.323,2.156 true 2.135,2.073 2.344,2.271 0.208,0.198 10 false *a 4.76,2.104 5.073,2.26 0.313,0.156 10 false *b
*a Pivot of the front wiper crank sub-assembly *b Windshield wiper link No. 1 rod



g.

Tighten the nut to install the front wiper crank sub-assembly.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


h.
E288190
0.74,1.792 1.083,1.448 true 0.615,1.792 0.927,2.031 0.313,0.24 10 false *a
*a Pivot of the front wiper crank sub-assembly


Apply MP grease to the pivot of the front wiper crank sub-assembly.


i.
E288187
1.813,1.063 1.25,0.885 false 0.5,1.958 0.781,1.74 false 1.052,0.76 1.365,0.917 0.313,0.156 10 false *a 0.323,1.948 0.635,2.104 0.313,0.156 10 false *b
*a Windshield Wiper Link No. 1 Rod
*b Pivot of the front wiper crank sub-assembly


Connect the windshield wiper link No. 1 rod to the pivot of the front wiper crank sub-assembly.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E288185
0.802,2.938 0.646,2.781 true 0.813,2.927 1.052,3.146 0.24,0.219 10 true *a
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Connect the connector.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides as shown in the illustration.

E288182


b.

Engage the 3 guides and 6 claws to install the cowl top ventilator louver sub-assembly as shown in the illustration.

E288180


c.

Install the 2 clips.


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Engage the 2 claws to install the front fender to cowl side seal LH.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reusing the front wiper arm and blade assembly LH:

i.
E288192
1.74,1.323 2.563,0.906 true 1.906,3.49 2.51,3.438 true 2.573,0.771 2.885,0.927 0.313,0.156 10 false *a 2.563,3.344 2.875,3.5 0.313,0.156 10 false *b
*a Wiper Arm Serration
*b Wiper Pivot Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.
E288194
1.313,2.792 1.708,2.479 true 1.698,2.344 2.01,2.5 0.313,0.156 10 false *a 0.844,2.583 1,2.781 0.156,0.198 10 false A 0.854,2.885 1.01,3.083 0.156,0.198 10 false A
*a Dot


Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10.0 mm (0.394 in.)



Hide 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reusing the front wiper arm and blade assembly RH:

i.
E288193
1.76,1.042 2.563,0.521 true 1.948,3.656 2.75,3.135 true 2.583,0.344 2.896,0.5 0.313,0.156 10 false *a 2.792,3.021 3.104,3.177 0.313,0.156 10 false *b
*a Wiper Arm Serration
*b Wiper Pivot Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.
E288195
1.604,2.781 2.042,2.5 true 2.083,2.354 2.396,2.51 0.313,0.156 10 false *a 1.198,2.417 1.354,2.615 0.156,0.198 10 false A 1.104,2.719 1.26,2.917 0.156,0.198 10 false A
*a Dot


Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10.0 mm (0.394 in.)



e.

Turn the ignition switch to ON.


f.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not come into contact with the vehicle body.


g.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


h.

Turn the ignition switch off.


Hide 85292B 9.INSTALL FRONT WIPER ARM HEAD CAP

a.
E288173

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.