Wear protective gloves. Sharp areas on the seat frame may injure your hands.
72170
1.INSTALL REAR SEAT OUTER TRACK ASSEMBLY LH
Install the rear seat outer track assembly LH to the rear seat track adjusting handle as shown in the illustration.
Make sure the handle is straight when installing it, and check that it is centered.
72190
2.INSTALL REAR SEAT INNER TRACK ASSEMBLY LH
Install the rear seat inner track assembly LH to the rear seat track adjusting handle as shown in the illustration.
Make sure the handle is straight when installing it, and check that it is centered.
71016A
3.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Install the rear seat track rail bracket LH.
Install the rear seat cushion frame sub-assembly LH with the 6 nuts.
71018
4.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
Using a T45 "TORX" socket wrench, install the rear seatback frame sub-assembly to the rear seat cushion frame sub-assembly with the 5 bolts as shown in the illustration.
72704F
5.INSTALL NO. 3 REAR SEAT RECLINING CONTROL CABLE
Engage the 8 cable clamps to install the No. 3 rear seat reclining control cable.
Install 2 new wire harness clamps.
72210H
6.INSTALL NO. 1 REAR SEAT TRACK CONTROL CABLE ASSEMBLY
Engage the 6 cable clamps to install the No. 1 rear seat track control cable assembly.
72704G
7.INSTALL NO. 4 REAR SEAT RECLINING CONTROL CABLE
Engage the 2 cable clamps to install the No. 4 rear seat reclining control cable.
Install 2 new wire harness clamps.
72552E
8.INSTALL RECLINING HINGE COVER LH
Engage the 3 guides to install the reclining hinge cover LH.
71834A
9.INSTALL NO. 1 REAR SEAT RECLINING COVER LH
Engage the 2 guides.
Install the No. 1 rear seat reclining cover LH with the screw.
73480A
10.INSTALL REAR SEAT INNER BELT ASSEMBLY LH
71639
11.INSTALL REAR SEAT CUSHION HINGE COVER LH
Engage the 2 guides and clip to install the rear seat cushion hinge cover LH.
| *A | w/ Seat Heater System |
Engage the clamp.
w/ Seat Heater System:
Engage the 2 clamps.
71826B
12.INSTALL REAR SEAT CUSHION MOULDING LH
Engage the guide and 6 claws.
Install the rear seat cushion moulding LH with the screw.
71829B
13.INSTALL REAR SEAT REAR CUSHION MOULDING
Engage the guide and 6 claws.
Install the rear seat rear cushion moulding with the screw.
87510S
14.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)
71078S
15.INSTALL SEPARATE TYPE REAR SEATBACK COVER
Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 9 new hog rings.
Be careful not to damage the separate type rear seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.
16.INSTALL REAR SEATBACK COVER WITH PAD
Temporarily install the rear seatback cover with pad to the rear seatback frame sub-assembly.
Engage the 2 hooks.
w/ Seat Heater System:
| *a | Clamp |
| *b | Wire Harness Clamp |
Engage the clamp.
Install a new wire harness clamp.
Engage the 6 hooks.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the rear seatback cover with pad.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad.
71931B
17.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.
71866A
18.INSTALL NO. 2 REAR SEAT COVER BEZEL
Install the No. 2 rear seat cover bezel with the 3 screws.
72616A
19.INSTALL REAR SEATBACK LOCK STRIKER COVER
Engage the 4 claws to install the 2 rear seatback lock striker covers.
72591
20.INSTALL RECLINING REMOTE CONTROL LEVER KNOB
Engage the claw to install the reclining remote control lever knob as shown in the illustration.
71890A
21.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY
Engage the 2 guides and 9 claws as indicated by the arrows, in the order shown in the illustration to install the rear seatback board carpet assembly.
72997
22.INSTALL REAR SEATBACK COVER
Engage the 4 claws to install the rear seatback cover.
87510R
23.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)
71076S
24.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
Using hog ring pliers, install 13 new hog rings.
Be careful not to damage the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.
Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 6 new hog rings.
Be careful not to damage the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.
25.INSTALL REAR SEAT CUSHION COVER WITH PAD
Engage the 2 hooks.
Engage the 14 hooks to install the rear seat cushion cover with pad.
87501D
26.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
27.CONNECT REAR SEAT CUSHION HEATER HARNESS (w/ Seat Heater System)
Engage the clamp to connect the rear seat cushion heater harness.
Connect the connector.
28.CONNECT REAR SEATBACK HEATER HARNESS (w/ Seat Heater System)
| *a | Clamp |
| *b | Wire Harness Clamp |
Engage the 2 clamps to connect the rear seatback heater harness.
Connect the connector.
Install a new wire harness clamp.
82194
29.INSTALL REAR SEAT WIRE (w/ Seat Heater System)
Engage the 6 clamps to install the rear seat wire.
Connect the connector.
82194
30.INSTALL REAR SEAT WIRE (w/ Seat Belt Warning System)
Engage the 6 clamps to install the rear seat wire.
Connect the connector.
72058A
31.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the 2 cable clamps.
Install a new wire harness clamp as shown in the illustration.
Engage the 3 guides.
Install the rear seat lock control lever sub-assembly with the 2 screws.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration.
72615H
32.INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER
Engage the guide and claw to install the rear No. 1 seatback lock striker cover as shown in the illustration.
72526E
33.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Install the reclining adjuster release handle with the 3 screws.
71846E
34.INSTALL REAR SEAT COVER CAP
Engage the 3 claws to install the rear seat cover cap.