Wear protective gloves. Sharp areas on the seat frame may injure your hands.
71846E
1.REMOVE REAR SEAT COVER CAP
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws and remove the rear seat cover cap as shown in the illustration.
72526E
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE
Remove the 3 screws and reclining adjuster release handle.
72615H
3.REMOVE REAR NO. 1 SEATBACK LOCK STRIKER COVER
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and guide, and remove the rear No. 1 seatback lock striker cover as shown in the illustration.
| *a | Protective Tape | - | - |
72058A
4.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Remove the 2 hog rings.
Remove the 2 screws.
Disengage the 3 guides.
Remove the wire harness clamp as shown in the illustration.
Disengage the 2 cable clamps and remove the rear seat lock control lever sub-assembly.
82194
5.REMOVE REAR SEAT WIRE (w/ Seat Belt Warning System)
Disconnect the connector.
Disengage the 6 clamps and remove the rear seat wire.
82194
6.REMOVE REAR SEAT WIRE (w/ Seat Heater System)
Disconnect the connector.
Disengage the 6 clamps and remove the rear seat wire.
7.DISCONNECT REAR SEATBACK HEATER HARNESS (w/ Seat Heater System)
| *a | Clamp |
| *b | Wire Harness Clamp |
Remove the wire harness clamp.
Disconnect the connector.
Disengage the 2 clamps and disconnect the rear seatback heater harness.
8.DISCONNECT REAR SEAT CUSHION HEATER HARNESS (w/ Seat Heater System)
Disconnect the connector.
Disengage the clamp and disconnect the rear seat cushion heater harness.
87501D
9.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
10.REMOVE REAR SEAT CUSHION COVER WITH PAD
Disengage the 14 hooks.
Disengage the 2 hooks and remove the rear seat cushion cover with pad.
71076S
11.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 6 hog rings.
Remove the 13 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.
87510R
12.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
72997
13.REMOVE REAR SEATBACK COVER
Disengage the 4 claws and remove the rear seatback cover.
71890A
14.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY
Disengage the 9 claws and 2 guides, and remove the rear seatback board carpet assembly as indicated by the arrows, in the order shown in the illustration.
72591
15.REMOVE RECLINING REMOTE CONTROL LEVER KNOB
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining remote control lever knob as indicated by the arrows, in the order shown in the illustration.
| *a | Protective Tape | - | - |
72616A
16.REMOVE REAR SEATBACK LOCK STRIKER COVER
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the 2 rear seatback lock striker covers.
71866A
17.REMOVE NO. 2 REAR SEAT COVER BEZEL
Remove the 3 screws and No. 2 rear seat cover bezel.
71931B
18.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Disengage the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
19.REMOVE REAR SEATBACK COVER WITH PAD
Remove the 2 hog rings.
Disengage the 6 hooks.
w/ Seat Heater System:
Remove the wire harness clamp.
| *a | Clamp |
| *b | Wire Harness Clamp |
Disengage the clamp.
Disengage the 2 hooks and remove the rear seatback cover with pad.
71078S
20.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the 9 hog rings and the separate type rear seatback cover from the separate type seatback pad.
87510S
21.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
71829B
22.REMOVE REAR SEAT REAR CUSHION MOULDING
Remove the screw.
Disengage the 6 claws.
Disengage the guide and remove the rear seat rear cushion moulding.
71826B
23.REMOVE REAR SEAT CUSHION MOULDING LH
Remove the screw.
Disengage the 6 claws.
Disengage the guide and remove the rear seat cushion moulding LH.
71639
24.REMOVE REAR SEAT CUSHION HINGE COVER LH
| *A | w/ Seat Heater System |
w/ Seat Heater System:
Disengage the 2 clamps.
Disengage the clamp.
Disengage the clip and 2 guides, and remove the rear seat cushion hinge cover LH.
73480A
25.REMOVE REAR SEAT INNER BELT ASSEMBLY LH
71834A
26.REMOVE NO. 1 REAR SEAT RECLINING COVER LH
Remove the screw.
Disengage the 2 guides and remove the No. 1 rear seat reclining cover LH.
72552E
27.REMOVE RECLINING HINGE COVER LH
Disengage the 3 guides and remove the reclining hinge cover LH.
72704G
28.REMOVE NO. 4 REAR SEAT RECLINING CONTROL CABLE
Remove the 2 wire harness clamps.
Disengage the 2 cable clamps and remove the No. 4 rear seat reclining control cable.
72210H
29.REMOVE NO. 1 REAR SEAT TRACK CONTROL CABLE ASSEMBLY
Disengage the 6 cable clamps and remove the No. 1 rear seat track control cable assembly.
72704F
30.REMOVE NO. 3 REAR SEAT RECLINING CONTROL CABLE
Remove the 2 wire harness clamps.
Disengage the 8 cable clamps and remove the No. 3 rear seat reclining control cable.
71018
31.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY
Using a T45 "TORX" socket wrench, remove the 5 bolts and rear seatback frame sub-assembly from the rear seat cushion frame sub-assembly as shown in the illustration.
71016A
32.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Lift up the rear seat track adjusting handle and move the rear seat cushion frame sub-assembly LH to the foremost position.
Remove the 6 nuts and rear seat cushion frame sub-assembly LH.
Remove the rear seat track rail bracket LH.
72190
33.REMOVE REAR SEAT INNER TRACK ASSEMBLY LH
Using a screwdriver, remove the rear seat inner track assembly LH from the rear seat track adjusting handle as shown in the illustration.
Insert the screwdriver into the hole shown in the illustration.
72170
34.REMOVE REAR SEAT OUTER TRACK ASSEMBLY LH
Using a screwdriver, remove the rear seat outer track assembly LH from the rear seat track adjusting handle as shown in the illustration.
Insert the screwdriver into the hole shown in the illustration.