Wear protective gloves. Sharp areas on the seat frame may injure your hands.
72868
1.REMOVE CENTER ARMREST HINGE COVER RH
Disengage the claw and guide, and remove the center armrest hinge cover RH as shown in the illustration.
72830
2.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Remove the bolt and No. 2 rear seat center armrest plate.
Disengage the 2 guides and remove the rear seat center armrest assembly as shown in the illustration.
72831B
3.REMOVE NO. 1 REAR SEAT CENTER ARMREST PLATE
Remove the No. 1 rear seat center armrest plate as shown in the illustration.
72806D
4.REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
Disengage the 2 claws and 2 guides, and remove the rear seat center armrest cup holder sub-assembly as shown in the illustration.
72087
5.REMOVE REAR NO. 1 SEAT CENTER ARMREST COVER
Open the fastener as indicated by the arrows, in the order shown in the illustration.
Remove the rear No. 1 seat center armrest cover from the rear No. 1 seat center armrest pad as shown in the illustration.
71828B
6.REMOVE REAR SEAT REAR CUSHION MOULDING RH
Disengage the clip and 9 claws.
Disengage the guide and remove the rear seat cushion moulding RH as shown in the illustration.
73380D
7.REMOVE REAR SEAT INNER BELT ASSEMBLY
71845D
8.REMOVE REAR SEAT COVER CAP
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws and remove the rear seat cover cap as shown in the illustration.
72525C
9.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE
Remove the 3 screws and No. 1 reclining adjuster release handle.
72615H
10.REMOVE REAR NO. 1 SEATBACK LOCK STRIKER COVER
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and guide, and remove the rear No. 1 seatback lock striker cover as shown in the illustration.
| *a | Protective Tape | - | - |
72058A
11.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
| *a | Hook |
| *b | Hog Ring |
Remove the 2 hog rings.
Disengage the hook.
Remove the 2 screws.
Disengage the 3 guides.
Remove the wire harness clamp as shown in the illustration.
Disengage the 2 cable clamps and remove the rear seat lock control lever sub-assembly.
71485B
12.REMOVE REAR SEAT HINGE COVER
Remove the screw.
Disengage the 3 claws and remove the rear seat hinge cover.
73350A
13.DISCONNECT REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY
82194
14.REMOVE REAR SEAT WIRE (w/ Seat Belt Warning System)
Disconnect the connector.
Disengage the 6 clamps and remove the rear seat wire.
82194
15.REMOVE REAR SEAT WIRE (w/ Seat Heater System)
Disconnect the connector.
Disengage the 6 clamps and remove the rear seat wire.
16.DISCONNECT REAR SEATBACK HEATER HARNESS (w/ Seat Heater System)
| *a | Clamp |
| *b | Wire Harness Clamp |
Disconnect the connector.
Remove the wire harness clamp.
Disengage the 2 clamps and disconnect the rear seatback heater harness.
17.DISCONNECT REAR SEAT CUSHION HEATER HARNESS (w/ Seat Heater System)
Disconnect the connector.
Disengage the clamp and disconnect the rear seat cushion heater harness.
87501D
18.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
19.REMOVE REAR SEAT CUSHION COVER WITH PAD
Disengage the 19 hooks and remove the rear seat cushion cover with pad.
71076S
20.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 8 hog rings.
Remove the 13 hog rings and separate type rear seat cushion cover.
87510P
21.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
73380A
22.REMOVE REAR SEAT INNER BELT ASSEMBLY RH
72996A
23.REMOVE REAR SEATBACK COVER
Disengage the 4 claws and remove the rear seatback cover.
72996
24.REMOVE REAR SEATBACK COVER RH
Disengage the 4 claws and remove the rear seatback cover RH.
71880A
25.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY
Disengage the 11 claws and 4 guides, and remove the rear seatback board carpet assembly as indicated by the arrows, in the order shown in the illustration.
72593C
26.REMOVE NO. 2 RECLINING REMOTE CONTROL LEVER KNOB
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the No. 2 reclining remote control lever knob as indicated by the arrows, in the order shown in the illustration.
| *a | Protective Tape | - | - |
72615A
27.REMOVE REAR SEATBACK LOCK STRIKER COVER
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the 2 rear seatback lock striker covers.
71865
28.REMOVE REAR NO. 1 SEAT COVER BEZEL
Remove the 3 screws and rear No. 1 seat cover bezel.
71931B
29.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
for RH Side:
Disengage the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
for Center:
Disengage the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
73178A
30.REMOVE SEAT BELT ANCHOR COVER CAP
Disengage the 2 claws and remove the seat belt anchor cover cap.
73373
31.REMOVE REAR SEAT SHOULDER BELT COVER
Disengage the 2 claws and 2 guides.
Remove the rear seat shoulder belt cover as shown in the illustration.
32.REMOVE REAR SEATBACK COVER WITH PAD
Remove the 2 hog rings.
Disengage the 12 hooks.
w/ Seat Heater System:
| *a | Clamp |
| *b | Wire Harness Clamp |
Disengage the 2 clamps.
Remove the wire harness clamp.
Disengage the 2 hooks and remove the rear seatback cover with pad.
71078S
33.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the 8 hog rings.
Remove the 9 hog rings and separate type rear seatback cover from the separate type rear seatback pad.
87510Q
34.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
73117A
35.REMOVE BELT PROTECTOR
73373A
36.REMOVE REAR SEAT SHOULDER BELT COVER RH
73350A
37.REMOVE REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY
71829B
38.REMOVE REAR SEAT REAR CUSHION MOULDING
Remove the screw.
Disengage the 6 claws and guide, and remove the rear seat rear cushion moulding.
71485
39.REMOVE REAR SEAT HINGE COVER
Remove the screw.
Disengage the 2 guides and remove the rear seat hinge cover.
71833A
40.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
Disengage the clamp.
Disengage the clip and 5 claws, and remove the rear No. 1 seat reclining cover RH.
72996E
41.REMOVE REAR NO. 1 SEAT INNER SHIELD COVER
Disengage the guide and remove the rear No. 1 seat inner shield cover as shown in the illustration.
71486C
42.REMOVE REAR SEAT HINGE COVER LH
Remove the screw.
Disengage the guide and remove the rear seat hinge cover LH.
72551A
43.REMOVE RECLINING HINGE COVER
Disengage the 2 claws and guide and remove the reclining hinge cover.
71629
44.REMOVE REAR SEAT CUSHION HINGE COVER
Disengage the 2 guides and remove the rear seat cushion hinge cover.
72704B
45.REMOVE NO. 2 REAR SEAT RECLINING CONTROL CABLE
Remove the 2 wire harness clamps.
Disengage the 2 cable clamps and remove the No. 2 rear seat reclining control cable.
72210G
46.REMOVE NO. 1 REAR SEAT TRACK CONTROL CABLE ASSEMBLY
Disengage the 6 cable clamps and remove the No. 1 rear seat track control cable assembly.
72704A
47.REMOVE REAR SEAT RECLINING CONTROL CABLE
Remove the 2 wire harness clamps.
Disengage the 8 cable clamps and remove the rear seat reclining control cable.
71018
48.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY
Remove the 2 bolts.
Using a T45 "TORX" socket wrench, remove the 3 bolts and rear seatback frame sub-assembly from the rear seat cushion frame sub-assembly as shown in the illustration.
71015
49.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Lift up the rear seat track adjusting handle and move the rear seat cushion frame sub-assembly RH to the foremost position.
Remove the 6 nuts and rear seat cushion frame sub-assembly RH.
72180C
50.REMOVE REAR SEAT INNER TRACK ASSEMBLY RH
Using a screwdriver, remove the rear seat inner track assembly RH from the rear seat track adjusting handle as shown in the illustration.
Insert the screwdriver into the hole shown in the illustration.
72160
51.REMOVE REAR SEAT OUTER TRACK ASSEMBLY RH
Using a screwdriver, remove the rear seat outer track assembly RH from the rear seat track adjusting handle as shown in the illustration.
Insert the screwdriver into the hole shown in the illustration.