Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0101297 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION (for Glass Hatch Type)

NOTICE:
·

Be sure to use the centering jig when removing and installing the rear wiper motor assembly. Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly, causing the wiping angle to change.

·

After installing the rear wiper motor assembly, do not open the glass hatch before installing the rear wiper link.

·

If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.



Hide 64783A 2.REMOVE BACK WINDOW UPPER TRIM PANEL

Hide 64792 3.REMOVE BACK DOOR TRIM COVER LH

Hide 64791C 4.REMOVE BACK DOOR TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64798 5.REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)

Hide 67766 6.REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER

Hide 67765A 7.REMOVE NO. 1 BACK DOOR SERVICE HOLE COVER

Hide 64780A 8.REMOVE BACK DOOR TRIM PANEL ASSEMBLY

Hide 85132A 9.REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)

a.
E288207C01
0,0 0,0 false
V100155

Fastener


Disengage the 3 clips.


b.

Disengage the fastener and remove the rear wiper shaft cover.


Hide 85292A 10.REMOVE REAR WIPER ARM HEAD CAP

a.
E288208

Disengage the 2 claws as shown in the illustration.


b.
E288210

Disengage the 2 claws and remove the rear wiper arm head cap.


Hide 11.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

a.
E288211

Remove the nut and rear wiper arm and blade assembly.


Hide 85143R 12.REMOVE REAR WIPER MOTOR GROMMET (for Fixed Glass Type)

a.
E288212

Remove the rear wiper motor grommet.


Hide 85176R 13.REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)

a.
E288213

Remove the rear wiper link cap.


Hide 85148R 14.REMOVE REAR WIPER LINK PIVOT WITH WASHER PACKING (for Glass Hatch Type)

a.
E288214

Remove the nut and rear wiper link pivot with washer packing.


Hide 85110R 15.REMOVE REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)

a.
E288215

Disconnect the connector.


b.

Loosen the 4 bolts and remove the rear wiper motor assembly.

NOTICE:

Be careful not to scratch the back door glass.



Hide 85110R 16.REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

a.

When reusing the rear wiper motor assembly:

i.

Open the glass hatch.


ii.
E288217

Engage the 3 claws and 2 guides to install the centering jig.

NOTICE:
·

The centering jig cannot be reused.

·

Do not remove the centering jig before installing the rear wiper link.




iii.
E288218

Close the glass hatch and engage the 2 claws and guide.

NOTICE:

Be sure to engage the 2 claws and guide securely.



iv.
E288219C01
0,0 0,0 false
V100136

Nut
V100137

Bolt


Disconnect the connector.


v.

Remove the 2 nuts.


vi.

Remove the 4 bolts and rear wiper motor assembly.

NOTICE:
·

Do not hold the rear wiper motor assembly by the rear wiper link.

·

Be careful not to scratch the back door glass.





b.

When using a new rear wiper motor assembly:

i.
E288221

Disconnect the connector.


ii.

Remove the 4 bolts.


iii.
E288222

Remove the 2 nuts and rear wiper motor assembly.

NOTICE:

Be careful not to scratch the back door glass.