Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0101297 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION (for Glass Hatch Type)

NOTICE:
·

Be sure to use the centering jig when removing and installing the rear wiper motor assembly. Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly, causing the wiping angle to change.

·

After installing the rear wiper motor assembly, do not open the glass hatch before installing the rear wiper link.

·

If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.



Hide 85143R 2.INSTALL REAR WIPER MOTOR GROMMET (for Fixed Glass Type)

a.
E288223C01
1.333,0.792 1.729,1.094 1.729,1.094 2.073,0.792 true 1.646,1.125 1.958,1.281 0.313,0.156 10 false *a
*a Rear Wiper Motor Grommet Lip


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.
E288306C01
2.115,0.26 2.573,0.323 true 1.938,0.146 2.25,0.302 0.313,0.156 10 false *a
*a Alignment Mark


Install the rear wiper motor grommet.

HINT:

Install the grommet with its alignment mark facing up.



Hide 85110R 3.INSTALL REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)

a.

Insert the shaft of the rear wiper motor assembly into the rear wiper motor grommet.


b.
E288216

Install the rear wiper motor assembly with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

Be careful not to scratch the back door glass.



c.

Connect the connector.


Hide 85110R 4.INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

a.
E288220C01
0.365,2.208 0.573,2.458 0.208,0.25 10 true 1 2.896,1.052 3.104,1.302 0.208,0.25 10 true 2 0.365,2.979 0.573,3.229 0.208,0.25 10 true 3 2.646,3.01 2.854,3.26 0.208,0.25 10 true 4 2.24,0.323 2.448,0.573 0.208,0.25 10 true 5 0.188,0.188 0.365,0.427 0.177,0.24 10 true 6
V100135

Bolt
V100136

Nut


Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

NOTICE:
·

Do not hold the rear wiper motor assembly by the rear wiper link.

·

Be careful not to scratch the back door glass.

·

Do not remove the centering jig before installing the rear wiper link.




b.

Tighten the 4 bolts and 2 nuts to install the rear wiper motor assembly.

HINT:

Tighten the bolts and nuts in the order shown in the illustration.


Torque:
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Disengage the 2 claws and guide and open the glass hatch.


d.

Disengage the 3 claws and 2 guides to remove the centering jig.


e.

Close the glass hatch.


Hide 85148R 5.INSTALL REAR WIPER LINK PIVOT WITH WASHER PACKING (for Glass Hatch Type)

a.

Install the rear wiper link pivot with washer packing with the nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 85176R 6.INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)

a.
E288225C02
1.323,0.781 1.719,1.094 1.719,1.094 2.083,0.781 true 1.656,1.125 1.969,1.281 0.313,0.156 10 false *a
*a Rear Wiper Link Cap Lip


Apply MP grease to the entire surface of the rear wiper link cap lip.

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.

Install the rear wiper link cap.


Hide 7.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
E288226C01
0.969,1.094 1.729,1.396 true 1.865,3.771 2.448,3.594 true 0.792,0.969 1.104,1.125 0.313,0.156 10 false *a 2.469,3.49 2.781,3.646 0.313,0.156 10 false *b
*a Wiper Arm Serration
*b Wiper Pivot Serration


When reusing the rear wiper arm and blade assembly:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the rear wiper motor assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the rear wiper motor assembly at the automatic stop position.


d.
E288227C01
1.073,2.896 1.354,2.563 true 0.906,2.896 1.135,3.135 0.229,0.24 10 true *a 2.24,2.354 2.396,2.552 0.156,0.198 10 true A 2.25,2.51 2.406,2.708 0.156,0.198 10 true B
*a Dot


Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 15.0 mm (0.591 in.)
B 5.0 mm (0.197 in.)



e.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not come into contact with the vehicle body.


f.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


Hide 85292A 8.INSTALL REAR WIPER ARM HEAD CAP

a.

Engage the 2 claws.


b.
E288209

Close the rear wiper arm head cap as shown in the illustration.


c.

Engage the 2 claws to install the rear wiper arm head cap.


Hide 85132A 9.INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)

a.

Engage the 3 clips.


b.

Engage the fastener to install the rear wiper shaft cover.


Hide 64780A 10.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

Hide 67766 11.INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER

Hide 67765A 12.INSTALL NO. 1 BACK DOOR SERVICE HOLE COVER

Hide 64798 13.INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type)

Hide 64792 14.INSTALL BACK DOOR TRIM COVER LH

Hide 64791C 15.INSTALL BACK DOOR TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64783A 16.INSTALL BACK WINDOW UPPER TRIM PANEL