Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2013.12–2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0108076 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47371B 4.SEPARATE NO. 6 BRAKE TUBE CLAMP

a.
C292823

Remove the bolt and separate the No. 6 brake tube clamp.


Hide 88704 5.SEPARATE SUCTION HOSE SUB-ASSEMBLY

a.
C292824

Disengage the clamp to separate the suction hose sub-assembly from the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




b.

for 1AR-FE:

i.
C292923

Remove the bolt and separate the suction hose sub-assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.





c.

for 2GR-FE:

i.
C292825

Disengage the claw to separate the suction hose sub-assembly from the suction hose clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.





Hide 6.SEPARATE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.
C292826

Disengage the clamp to separate the air conditioner tube and accessory assembly from the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




b.
C292827

Remove the bolt and separate the air conditioner tube and accessory assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 7.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C292828
0,0 0,0 false
V100135

Release the lock lever
V100136

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C292830
1.49,1.167 0.865,1.625 true 1.865,1.125 2.385,1.542 true 2.021,0.75 2.563,0.75 true 0.708,0.792 1.25,0.792 true 1.073,0.323 1.479,0.74 true 2.208,0.302 1.792,0.719 true 2.344,1.583 2.656,1.74 0.313,0.156 10 true *a 0.771,1.646 1.083,1.802 0.313,0.156 10 true *b 2.573,0.667 2.885,0.823 0.313,0.156 10 true *c 2.219,0.229 2.531,0.385 0.313,0.156 10 true *d 0.885,0.208 1.052,0.375 0.167,0.167 10 true *e 0.531,0.719 0.708,0.885 0.177,0.167 10 true *f
*a for LHD: From 1st Chamber of Brake Master Cylinder Sub-assembly
for RHD: From 2nd Chamber of Brake Master Cylinder Sub-assembly
*b for LHD: From 2nd Chamber of Brake Master Cylinder Sub-assembly
for RHD: From 1st Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


d.
C292831

Remove the 3 bolts.


e.

Disengage the claw to remove the brake actuator with bracket.

NOTICE:
·

Do not damage the brake lines.

·

Do not deform the refrigerant lines.

·

Do not hold the brake actuator assembly by the connector.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines and refrigerant lines.



Hide 44510 8.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C292832

Disengage the 2 claws to remove the piping clamp.


b.
C292833

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.