Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108188 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B360751C01
0.688,0.083 1,0.24 0.313,0.156 10 false *a 2.5,0.083 2.813,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas "a" through "n" are within each standard range.

B362132
2.365,0.313 2.521,0.51 0.156,0.198 10 false a 2.427,1.156 2.583,1.354 0.156,0.198 10 false b 3.854,0.313 4.01,0.51 0.156,0.198 10 false c 3.927,1.156 4.083,1.354 0.156,0.198 10 false d 6.115,1.542 6.271,1.74 0.156,0.198 10 false e 6.604,3 6.76,3.198 0.156,0.198 10 false f 5.802,4.479 5.958,4.677 0.156,0.198 10 false g 6.01,4.219 6.167,4.417 0.156,0.198 10 false h 3.188,4.51 3.344,4.708 0.156,0.198 10 false i 2.594,4.271 2.75,4.469 0.156,0.198 10 false j 0.917,3.042 1.073,3.24 0.156,0.198 10 false k 0.313,2.813 0.469,3.01 0.156,0.198 10 false l 1.281,1.5 1.438,1.698 0.156,0.198 10 false m 0.719,1.281 0.875,1.479 0.156,0.198 10 false n

Standard Clearance
Area Measurement Area Measurement
a 3.35 to 6.35 mm (0.132 to 0.250 in.) b 0.65 to 6.35 mm (0.0256 to 0.250 in.)
c 3.35 to 6.35 mm (0.132 to 0.250 in.) d 0.75 to 3.75 mm (0.0295 to 0.148 in.)
e 4.5 to 8.5 mm (0.177 to 0.335 in.) f 4.5 to 8.5 mm (0.177 to 0.335 in.)
g 3.5 to 5.5 mm (0.138 to 0.217 in.) h -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
i 3.2 to 5.6 mm (0.126 to 0.220 in.) j -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
k 3.2 to 5.6 mm (0.126 to 0.220 in.) l -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
m 4.3 to 6.3 mm (0.169 to 0.248 in.) n -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)


Hide 2.ADJUST REAR DOOR

NOTICE:

Make sure to turn the ignition switch off when adjusting door lock strikers.


a.
B362130

Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the 4 hinge bolts on the door and adjust the door position.


d.

Tighten the 4 hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B362131

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)