Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM3160E _54 Brake _019694 BRAKE (FRONT) _0109275 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C291522
1.917,1.01 2.833,0.969 2.833,0.969 1.927,1.052 true 2.875,0.885 3.188,1.042 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.


Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
104 N*m (1061 kgf*cm, 77 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C211756
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47715D 4.INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.
C291533
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 2 disc brake cylinder slide pin.


b.

Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.


c.
C291534C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.


d.

Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.


e.

Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 47715A 5.INSTALL FRONT NO. 1 DISC BRAKE CYLINDER SLIDE PIN

a.
C291532
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 1 disc brake cylinder slide pin.


b.

Install the front No. 1 disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front No. 1 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 6.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C256897
0.792,0.594 1.083,0.594 false 2.333,0.604 2.625,0.604 false 0.781,3.917 1.073,3.917 false 2.333,3.906 2.625,3.906 false 1.323,4.271 1.708,4.365 1.708,4.365 2.094,4.271 true 0.625,3.844 0.938,4 0.313,0.156 10 false *1 2.667,3.833 2.979,3.99 0.313,0.156 10 false *2 2.667,0.531 2.979,0.688 0.313,0.156 10 false *3 0.615,0.521 0.927,0.677 0.313,0.156 10 false *4 1.635,4.385 1.948,4.583 0.313,0.198 10 false *a
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate
*3 Front No. 3 Disc Brake Pad Support Plate
*4 Front No. 4 Disc Brake Pad Support Plate
*a Protrusion


Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.


HINT:

The front disc brake pad support plate (lower) can be identified by its protrusion.



Hide 04945 7.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn front disc brake pads, the front disc brake anti-squeal shim kit must be replaced together with the front disc brake pads.

·

Make sure that disc brake grease is not applied onto the lining surface.

·

Install each front disc brake pad wear indicator plate in the correct position and direction.

·

Install the front disc brake anti-squeal shims in the correct positions and directions.



a.
C256926
0,0 0,0 false
V100155

Disc Brake Grease


Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.


b.
C256927
1.531,0.156 1.802,0.156 false 2.281,0.448 2.552,0.448 false 0.333,0.76 0.604,0.76 false 2.823,1.573 3.094,1.573 false 0.177,0.677 0.49,0.833 0.313,0.156 10 false *1 1.844,0.073 2.156,0.229 0.313,0.156 10 false *2 3.135,1.49 3.365,1.771 0.229,0.281 10 false *1 2.594,0.375 2.906,0.531 0.313,0.156 10 false *2
*1 Front Disc Brake Anti-squeal Shim
*2 Front Disc Brake Pad Wear Indicator Plate


Install the front disc brake anti-squeal shim to each front disc brake pad.


c.

Install the front disc brake pad wear indicator plate to each front disc brake pad.


Hide 8.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the front disc brake pads or the front disc.



b.
C263983

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




Hide 47750 9.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




Hide 47313J 10.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 12.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)