Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0109284 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 88211B 1.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

E287772C01
1.271,0.24 1.583,0.396 0.313,0.156 10 false *a 0.292,1.01 0.604,1.167 0.313,0.156 10 false *b
*a Approx. 10 m (32.8 ft.)
*b Approx. 14 m (45.9 ft.)


CAUTION:

Radiofrequency radiation exposure information:

·

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

·

This equipment should be kept with minimum distance of 20 cm (7.87 in.) between the radiator (antenna) and your body at all times during adjustment.

·

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.



NOTICE:
·

Perform measurements on a level surface.

·

Make sure that no large metal objects are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.



a.

Before adjusting the radar beam axis, prepare the vehicle as follows.

i.

Check the tire pressure and adjust it if necessary.


ii.

Remove all excess weight from the vehicle (luggage, heavy objects, etc.).


iii.

Remove the cool air intake duct seal (Click here Vehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL).



b.
E287773C01
1.708,0.49 2.24,0.24 false 2.323,0.146 2.635,0.302 0.313,0.156 10 false *a
*a Level


Check and adjust the vertical direction of the radar sensor.

i.

Remove dust, oil and foreign matter from the radar sensor level rack.


ii.

Set a level on the radar sensor level rack.


iii.
E287774C01
2.406,1.604 2.542,1.813 false 2.26,1.094 2.698,1.094 false 2.042,1.313 1.865,1.792 false 2.969,3.313 2.542,3.646 false 2.573,1.823 2.885,1.979 0.313,0.156 10 false *a 1.688,1.771 2,1.927 0.313,0.156 10 false *b 3.021,3.177 3.333,3.333 0.313,0.156 10 false *c 0.49,1.417 0.802,1.573 0.313,0.156 10 false *d 1.073,0.813 1.385,0.969 0.313,0.156 10 false *e 2.781,1.031 3.094,1.188 0.313,0.156 10 false *f
*a Level
*b Air Bubble
*c Bolt
*d Vehicle Front
*e Vehicle Left
*f 0°


Check that the level's air bubble is within the red frame.

OK:

Level's air bubble is within red frame.


If the bubble is not within the red frame, use a screwdriver to adjust the bolt until the air bubble is within the red frame.

HINT:
·

The adjustable range within the level's red frame is +/- 0.2°.

·

The target angle is +0.2° (upward angle of 0.2°).

Result:
Adjustment Direction Adjustment Procedure Adjustment Angle
Upward Turn screwdriver to positive (+) side When screwdriver is turned once, adjustment changes by about 0.12°
Downward Turn screwdriver to negative (-) side






c.
E287775C01
1.729,1.479 1.198,0.979 false 0.635,1.885 1.115,1.979 1.115,1.979 0.896,1.656 false 0.979,0.885 1.292,1.042 0.313,0.156 10 false *1 1.135,2.021 1.594,2.219 0.458,0.198 10 false SST
*1 Millimeter Wave Radar Sensor


Adjust the reflector height.

i.

Adjust the reflector so that the center of SST (reflector) is the same height as the millimeter wave radar sensor.

SST
09870-60000  (09870-60010)
09870-60040  

HINT:

Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob) and a 5 m (16.4 ft.) tape measure.




d.

Place the reflector.

i.

Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground.

E287764C01
5.438,1.802 6.052,2.229 false 3.823,0.698 5.417,0.927 false 2.615,2.406 3.094,2.125 false 2.615,2.49 3.292,2.521 false 6.135,2.177 6.448,2.333 0.313,0.156 10 false *a 3.156,2.021 3.469,2.177 0.313,0.156 10 false *b 3.604,0.594 3.917,0.75 0.313,0.156 10 false *c 3.375,2.427 3.688,2.583 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Mark



ii.

Repeat for the front of the vehicle.

E287765C01
1.5,0.885 2.844,0.865 false 1.51,1.594 2.031,1.948 false 3.375,2 3.979,2.198 false 3.333,2.365 3.99,2.26 false 2.083,1.875 2.396,2.031 0.313,0.156 10 false *a 3.177,1.906 3.49,2.063 0.313,0.156 10 false *b 2.927,0.771 3.24,0.927 0.313,0.156 10 false *c 3.146,2.281 3.458,2.438 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Mark



iii.
E287776C01
1.604,1.094 1.219,0.729 false 0.406,0.208 0.719,0.365 0.313,0.156 10 false *a 1.021,0.625 1.333,0.781 0.313,0.156 10 false *b
*a Adjust center by moving string to right and left
*b Extend string through front center point


Set one end of the 10 m (32.8 ft.) string on the vehicle rear center point. Run the string over the vehicle front center point to a position 5 m (16.4 ft.) beyond the vehicle front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.


iv.

Place SST (reflector) at the marked position.

NOTICE:

Perform the operation as precisely as possible.


E292183C01
0.781,1.688 1.052,2 false 3.656,1.25 4,1.531 false 1.115,2.021 1.427,2.177 0.313,0.156 10 false *a 3.375,1.156 3.688,1.313 0.313,0.156 10 false *b 2.042,0.25 2.354,0.406 0.313,0.156 10 false *c 0.323,1.531 0.635,1.688 0.313,0.156 10 false *d
*a Reflector Placement Point *b Millimeter Wave Radar Sensor Position
*c 5000 mm (16.4 ft.) *d 11 mm (0.433 in.)




e.

Check the radar beam axis.

i.

When using the GTS:

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch on (IG).

3.

Turn the GTS on and turn the cruise control main switch on.

4.

Select "Connect to Vehicle".

5.

Select each item on the display screen and proceed to the next screen.

6.

Under "System Selection Menu", select "Radar Cruise".

7.

Select "Utility" from the display screen.

8.

Select "Beam Axis Adjustment" and proceed to the next screen.

9.

Follow the GTS display and continue with the adjustment.

CAUTION:

Do not come within 20 cm (7.87 in.) of the radar sensor.


NOTICE:
·

Turn the cruise control main switch on before pressing "Next".

·

Make sure there is at least 20 cm (7.87 in.) between the millimeter wave radar sensor and any nearby individuals.

·

If "Error beam axis" is displayed on the screen, press the "Yes" button, and repeat again.

·

Check that there are no metal objects in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).




Powertrain > Radar Cruise > Utility
Tester Display
Beam Axis Adjustment
50005 197 5266

ii.

Press the "Exit" button to finish beam axis adjustment.


iii.

Disconnect the GTS from the DLC3.



f.

After adjusting the radar beam axis, return the vehicle to its original condition.

i.

Install the cool air intake duct seal (Click here Vehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION).


ii.

If any heavy items were removed from the vehicle, return them (luggage, heavy objects, etc.).