DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door, Main Body or Entry & Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Status | Back door lock condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Half Latch SW | Latch switch signal | ON or OFF | ON: Back door lock motor open-latched
OFF: Back door lock motor full-latched or half-latched |
- |
| Closer Position SW | Sector switch signal | ON or OFF | ON: Back door lock sector gear in center position
OFF: Back door lock sector gear out of center position |
- |
| Courtesy SW | Back door courtesy switch signal | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| PBD Main SW | Door control switch signal | ON or OFF | ON: Door control switch on
OFF: Door control switch not off |
- |
| PBD Close SW | Back door control switch signal | ON or OFF | ON: Back door control switch pushed
OFF: Back door control switch not pushed |
- |
| IG SW | Engine switch signal | ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
"OFF" is also displayed for this item when the engine switch is on (ACC). |
| PBD Position (3/4-Open) | Load signal detected during back door closing operation (3/4 - Open) | Caution or OK | Caution: Load detected between back door 3/4 and fully open position during back door closing operation
OK: No load detected between back door 3/4 and fully open position during back door closing operation |
- |
| PBD Position (2/4-3/4) | Load signal detected during back door closing operation (2/4 - 3/4) | Caution or OK | Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation
OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation |
- |
| PBD Position (1/4-2/4) | Load signal detected during back door closing operation (1/4 - 2/4) | Caution or OK | Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation
OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation |
- |
| PBD Position (Close-1/4) | Load signal detected during back door closing operation (Close - 1/4) | Caution or OK | Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation
OK: No load detected between back door fully closed and 1/4 open position during back door closing operation |
- |
| Closed Position Initialization | Back door fully closed position memorized signal | Not Initialized or Initialized | Not Initialized: Back door fully closed position not memorized
Initialized: Back door fully closed position memorized |
- |
| PBD SW Operation | Power back door switch operation | ON or 0.8 s | Current customize setting displayed | - |
| PBD Buzz In Use | Function that makes the power back door buzzer sound when the power back door is operating. | OFF or ON | Current customize setting displayed | - |
| PBD Assist Open Operation | Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to ON (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. | OFF or ON | Current customize setting displayed | - |
| PBD Assist Close Operation | Function that enables or disables the power back door assist close operation. When PBD Assist Close is set to ON (enabled) the back door will close automatically when closing the back door by manual operation. | OFF or ON | Current customize setting displayed | - |
| Door Unlock with 1 Motion. | Function that selects the door or doors to be unlocked when the back door is locked and the key switch is pushed to operate the power back door system.* | BackDoor or ALL DOORS | Current customize setting displayed | - |
| One Motion | Function that operates the power back door by pushing the key switch when the back door is unlocked. | OFF, 1 Op, 2 Op, 0.8s or Not Use | Current customize setting displayed | - |
| One Motion with Unlock Door | Function that operates the power back door by pushing the key switch when the back door is locked or unlocked.* | OFF, Not Use, 2 Op or 0.8s | Current customize setting displayed | - |
| Power Back Door Opening Adjust | Function that changes the back door opening angle for the power back door system opening operation. | "1:Min", "2:Small", "3:Middle", "4:Large" or "5:Max" | Current customize setting displayed | - |
| #Codes | The number of DTCs | Min.: 0
Max.: 255 |
The number of DTCs | - |
*: for RHD
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open | Back door lock | Permit or Prohibit | Permit: Back door unlocked
Prohibit: Back door locked |
- |
| Back Door Open SW | Rear door control switc signal | ON or OFF | ON: Rear door control switc on
OFF: Rear door control switc off |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch assembly signal | ON or OFF | ON: Back door opener switch assembly on
OFF: Back door opener switch assembly off |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door / Active Test.
Perform the Active Test according to the display on GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Latch Release | Latch release operation | OFF or ON | - |
| PBD Open/Close | Power back door motor operation | OFF, Open or Close | - |
| PBD Buzzer | Power back door warning buzzer sound | OFF or ON | - |
| PBD Close SW Light | Back door control switch illumination | OFF or ON | - |