Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
71849
1.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
82192
2.INSTALL FRONT SEAT WIRE
Connect each connector and engage each clamp to install the front seat wire.
71538B
3.INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)
Engage the 3 claws and guide to install the LH seat front seat cushion edge protector LH.
71537C
4.INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)
Use the same procedure as for the LH side.
71538A
5.INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)
Engage the 3 claws and guide to install the RH seat front seat cushion edge protector LH.
71537C
6.INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)
Use the same procedure as for the LH side.
71874
7.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
71873
8.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
Use the same procedure as for the LH side.
85860B
9.INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)
Engage the 2 hooks to install the seat cushion climate control blower assembly.
Connect the connector.
85868A
10.INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET (w/ Climate Control Seat System)
Install the seat cushion climate control bracket to the seat cushion climate control blower assembly with the 2 screws.
85866
11.INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)
Engage the 2 claws to install the seat cushion climate control duct to the seat cushion climate control blower assembly.
73905
12.INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY RH (for Front Passenger Side)
w/ Front Seat Airbag Sub-assembly RH
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SRS SEAT CUSHION AIRBAG ASSEMBLY>INSTALLATION
87510L
13.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
w/o Variable Seat Cushion System:
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
w/ Variable Seat Cushion System:
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
15.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Driver Side)
w/o Variable Seat Cushion System:
Engage the 10 hooks to install the separate type front seat cushion cover with pad.
w/ Variable Seat Cushion System:
Using hog ring pliers, install the separate type front seat cushion cover with pad with 4 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Turn back the separate type front seat cushion cover with pad to its original position.
Engage the 6 hooks.
Engage the 4 hooks.
Engage the 4 hooks.
|
Fastener |
Engage the 2 fasteners.
w/ Seat Heater System:
Engage the 3 clamps.
16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Front Passenger Side)
Engage the 12 hooks and 2 clips to install the separate type front seat cushion cover with pad.
w/ Seat Heater System:
Engage the 3 clamps.
Engage the claw to install the connector.
8219B
17.INSTALL FRONT SEAT NO. 2 WIRE
Connect each connector and engage each clamp to install the front seat No. 2 wire.
71759B
18.INSTALL FRONT SEATBACK HOOK
Install the 2 front seatback hooks to the separate type front seatback spring assembly.
Engage the 2 claws.
71587B
19.INSTALL FRONT SEATBACK EDGE PROTECTOR
Engage each claw to install the 2 front seatback edge protectors.
85867A
20.INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)
Engage the 4 hooks to install the seatback climate control blower.
Install the clip.
Connect the connector.
73920A
21.INSTALL FRONT SEAT AIRBAG ASSEMBLY
87510N
22.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
23.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 4 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
24.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71930A
25.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
Engage each claw to install the 2 front seat headrest support assemblies.
w/ Climate Control Seat System:
Engage the 2 claws to connect the seatback climate control blower to the separate type front seatback pad.
| *a | Bracket |
Engage the 3 brackets and install the 2 nuts.
For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the brackets securely.
Turn back the separate type front seatback cover to its original position.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
26.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
|
Fastener |
Engage the fastener to secure the front seat airbag assembly wire harness.
Engage the clamp.
Connect the connector.
Engage the 2 hooks.
84928
27.INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Variable Seat Cushion System)
84920
28.INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side)
84922C
29.INSTALL FRONT POWER SEAT SWITCH (w/o Seat Position Memory System)
84070
30.INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Position Memory System)
84921A
31.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
84921B
32.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
71868A
33.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD
Engage the clamp.
Engage the claw and clip to install the front seat inner No. 1 cushion shield.
Install the 2 screws.
w/ Variable Seat Cushion System:
Engage the hook.
71812D
34.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)
w/ Variable Seat Cushion System:
Connect the connector to the variable cushion switch.
Connect the connector to the front lumbar power seat switch.
w/o Seat Position Memory System:
Connect the connector to the front power seat switch.
w/ Seat Position Memory System:
Connect the 2 connectors to the position control ECU and switch assembly.
|
Wire Harness Guide |
Install the wire harness to the wire harness guide.
Engage the 2 clamps.
Engage the 3 claws to close the wire harness cover.
Engage the guide.
Engage the claw and 3 guides.
Engage the guide.
Engage the 2 claws and clip to install the front seat cushion shield.
Engage the claw.
71811D
35.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
Connect the connector to the front power seat switch.
|
Wire Harness Guide |
Install the wire harness to the wire harness guide.
Engage the 2 clamps.
Engage the 3 claws to close the wire harness cover.
Engage the guide.
Engage the claw and 4 guides.
Engage the guide.
Engage the 2 claws and clip to install the front seat cushion shield.
Engage the claw.
71862
36.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
Engage the claw and guide to install the front seat inner cushion shield.
Engage the claw and 3 guides.
71861
37.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
Engage the claw and guide to install the front seat inner cushion shield.
Engage the claw and 4 guides.
71074S
38.CONNECT SEPARATE TYPE FRONT SEATBACK COVER (w/o Climate Control Seat System)
Connect the rubber band of the separate type front seatback cover.
71074S
39.CONNECT SEPARATE TYPE FRONT SEATBACK COVER (w/ Climate Control Seat System)
Engage the 2 hooks to connect the 2 rubber bands of the separate type front seatback cover.
73240
40.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73240
41.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
87501B
42.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
89178A
43.INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)