Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › 2013.12–2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109430 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48540 1.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C296521C01
1.063,2.542 1.469,2.813 1.469,2.813 1.719,2.813 true 1.75,2.719 2.01,2.906 0.26,0.188 10 false *a 1.417,0.583 1.625,0.802 0.208,0.219 10 true A 1.115,2.896 1.271,3.094 0.156,0.198 10 false B
*a Protector


Temporarily install the rear shock absorber assembly with the bolt (A), bolt (B) and nut.

NOTICE:
·

Ensure that the protector faces the front of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt (B) with the nut secured.

·

Fully tighten the bolts after stabilizing the suspension.




b.

Slowly lower the rear No. 2 suspension arm assembly.


Hide 2.STABILIZE SUSPENSION

a.
C293824C01
0.625,1.823 0.938,1.823 false 0.635,1.99 1.073,1.99 false 0.302,0.406 0.458,0.604 0.156,0.198 10 false A 0.458,1.719 0.615,1.917 0.156,0.198 10 false *a 0.469,1.896 0.625,2.104 0.156,0.208 10 false *b
*a Wooden Block
*b Jack
V100155

Wooden block placement location


Jack up the rear No. 2 suspension arm assembly, and place a wooden block underneath to avoid damage. Apply load to the suspension so that the rear upper control arm assembly is positioned as shown in the illustration.

Standard Length (A):

24.3 mm (0.957 in.)


CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

If the rear upper control arm assembly cannot be positioned as shown in the illustration even when the rear No. 2 suspension arm assembly is jacked up, apply additional load to the vehicle such as by placing a weight in the luggage compartment.



Hide 48540 3.INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C293823N02
1.406,0.583 1.573,0.833 0.167,0.25 10 true A 1.094,2.906 1.25,3.104 0.156,0.198 10 true B

Install the rear shock absorber assembly with the bolt (A) and bolt (B).

Torque:
Bolt (A) : 100 N*m (1020 kgf*cm, 74 ft.*lbf)
Bolt (B) : 92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt (B) with the nut secured.



Hide 48738 4.INSTALL REAR SUSPENSION ARM COVER

Hide 5.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)