Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C1298/98  Linear Solenoid Circuit  


DESCRIPTION

The 4WD ECU assembly receives signals from each sensor to control clutch fluid pressure for limiting the center differential operation, which distributes torque according to the driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
C1298/98 Linear Solenoid Circuit When all of the following continue for 1 second or more:
·

The current requested by the 4WD linear solenoid (electro magnetic control coupling sub-assembly) is either 0 A or greater than 0.8 A.

·

Open or short occurs in the linear solenoid circuit.


·

Wire harness and connector

·

4WD linear solenoid (Electro magnetic control coupling sub-assembly)

·

4WD ECU assembly


DTC stored

WIRING DIAGRAM

C279204E06
1.854,1.51 3.219,1.688 1.365,0.177 10 false 4WD Linear Solenoid 3.656,0.531 3.979,0.74 0.323,0.208 10 false SLC 3.667,1.052 4.021,1.229 0.354,0.177 10 false BSF 4.063,0.531 4.25,0.698 0.188,0.167 10 false 2 4.052,1.031 4.208,1.229 0.156,0.198 10 false 1 4.875,0.563 5.031,0.76 0.156,0.198 10 false 1 4.875,1.031 5.031,1.229 0.156,0.198 10 false 2 5.104,0.667 5.719,0.865 0.615,0.198 10 false SLC- 5.104,1.167 5.719,1.365 0.615,0.198 10 false SLC+ 5.073,2.198 5.531,2.396 0.458,0.198 10 false F14 5.073,2.365 6.531,2.563 1.458,0.198 10 false 4WD ECU Assembly 0.615,2.208 0.927,2.406 0.313,0.198 10 false O4 0.615,2.385 3.792,2.594 3.177,0.208 10 false Electro Magnetic Control Coupling Sub-assembly

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - TRANSMISSION COUPLING ASSEMBLY)
a.
C270074C30
2.427,0.104 2.833,0.365 0.406,0.26 1.417,1.917 1.25,1.917 1.25,1.917 1.094,1.167 true 0.5,1.917 0.667,1.917 0.667,1.917 0.75,1.167 false 1.49,1.833 1.979,2.021 0.49,0.188 10 false SLC+ 2.51,0.156 2.823,0.354 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a 0.167,1.833 0.583,2 0.417,0.167 10 false SLC-
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the F14 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-2 (SLC+) - F14-1 (SLC-) 20°C (68°F) 2.2 to 2.6 Ω
F14-2 (SLC+) - Body ground Always 10 kΩ or higher
F14-1 (SLC-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY
2.INSPECT ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY
a.
C131916C01
1.575,1.186 1.117,1.614 false 1.813,1.187 2.229,1.591 false 0.844,1.626 1.149,1.778 0.306,0.152 10 SLC 2.161,1.634 2.466,1.786 0.306,0.152 10 BSF 0,0 0.313,0.156 0.313,0.156 10 *a
*a Component without harness connected
(4WD Linear Solenoid (Electro Magnetic Control Coupling Sub-assembly))


Disconnect the O4 4WD linear solenoid (electro magnetic control coupling sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BSF) - 2 (SLC) 20°C (68°F) 2.2 to 2.6 Ω
1 (BSF) - Body ground Always 10 kΩ or higher
2 (SLC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY