Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C120C/79  Linear Solenoid Power Supply System Malfunction  


DESCRIPTION

This DTC is output by the 4WD ECU assembly if a malfunction occurs in the linear solenoid power supply system.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
C120C/79 Linear Solenoid Power Supply System Malfunction When one of the following conditions is met:
·

When the 4WD relay is on, the 4WD relay monitor remains off for 1 second or more while the voltage at the IG1 terminal is 9.5 V or more

·

When the 4WD relay is on, the 4WD relay monitor is not on for 1 second or more while the voltage at the IG1 terminal is less than 9.5 V

·

While the 4WD relay is off, the 4WD relay monitor remains on for 1 second or more immediately after the ignition switch is turned to ON


·

Wire harness and connector (IG1 circuit, GND circuit)

·

4WD ECU assembly


DTC stored

WIRING DIAGRAM

C284828E06
0.5,0.646 1.677,0.854 1.177,0.208 10 false from IG1 Circuit 3.104,0.833 3.781,1.021 0.677,0.188 10 false IG1 NO. 2 4.844,2.177 5.302,2.375 0.458,0.198 10 false F14 4.854,2.333 6.844,2.531 1.99,0.198 10 false 4WD ECU Assembly 5.104,0.677 5.563,0.875 0.458,0.198 10 false IG1 5.115,1.531 5.573,1.729 0.458,0.198 10 false GND 4.885,0.531 5.042,0.729 0.156,0.198 10 false 3 4.896,1.417 5.052,1.615 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C28
2.406,0.094 2.813,0.354 0.406,0.26 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the F14 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F14-3 (IG1) -Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C29
2.396,0.104 2.802,0.365 0.406,0.26 2.167,1.917 2.417,1.917 2.417,1.917 2.583,1.167 true 1.833,1.833 2.177,2.031 0.344,0.198 10 false GND 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-4 (GND) -Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Turn the ignition switch to ON.


c.

Check that no DTCs other than DTC C120C/79 have been output.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Result Proceed to
DTCs other than DTC C120C/79 are not output A
DTCs other than DTC C120C/79 are output B




A

B