Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB0 Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor main switch (warning canceling switch assembly) is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E233743E58
1.573,1.25 1.708,1.406 0.135,0.156 10 false 1 2.979,1.156 3.115,1.313 0.135,0.156 10 false 8 5.802,1.24 5.927,1.396 0.125,0.156 10 false 4 3.281,1.375 4.021,1.667 0.74,0.292 10 false BSL+ 5.99,1.354 6.396,1.51 0.406,0.156 10 false OMIL 3.281,1.833 3.646,1.99 0.365,0.156 10 false - 0.219,2.156 0.594,2.313 0.375,0.156 10 false IND1 5.885,3.396 6.333,3.552 0.448,0.156 10 false M31 1.375,1.354 1.51,1.51 0.135,0.156 10 false + 1.385,1.823 1.521,1.979 0.135,0.156 10 false - 1.583,1.719 1.719,1.875 0.135,0.156 10 false 2 2.927,1.625 3.125,1.781 0.198,0.156 10 false 12 0.219,2.323 1.271,2.49 1.052,0.167 10 false Outer Mirror LH 0.167,3.406 2.542,3.583 2.375,0.177 10 false Outer Rear View Mirror Assembly LH 5.885,3.573 7.083,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor LH 0.198,2.615 2.281,2.927 2.083,0.313 10 false (Outer Rear View Mirror Indicator LH) 2.896,1.344 3.24,1.51 0.344,0.167 10 false z10 2.885,1.813 3.271,1.99 0.385,0.177 10 false z10 3.219,3.396 4.458,3.76 1.24,0.365 10 false Outer Mirror Control ECU Assembly LH 4.01,1.354 4.417,1.51 0.406,0.156 10 false BDSL 4.073,1.823 4.438,1.979 0.365,0.156 10 false GND 4.594,1.146 4.781,1.302 0.188,0.156 10 false 13 4.646,1.615 4.781,1.771 0.135,0.156 10 false 7 4.604,1.354 5,1.521 0.396,0.167 10 false I2 4.604,1.823 4.938,2.031 0.333,0.208 10 false I2

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the M31 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M31-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND1 outer mirror LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M31-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the z10 outer mirror control ECU assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M31-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the I2 outer mirror control ECU assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M31-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR