Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor main switch (warning canceling switch assembly) is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E233743E59
1.573,1.24 1.708,1.396 0.135,0.156 10 false 1 2.958,1.156 3.094,1.313 0.135,0.156 10 false 8 5.802,1.24 5.927,1.396 0.125,0.156 10 false 4 3.281,1.375 3.75,1.552 0.469,0.177 10 false BSR+ 5.99,1.354 6.396,1.51 0.406,0.156 10 false OMIR 3.281,1.833 3.688,2 0.406,0.167 10 false - 0.219,2.156 0.594,2.313 0.375,0.156 10 false IND2 5.885,3.396 6.333,3.552 0.448,0.156 10 false L23 1.354,1.344 1.49,1.5 0.135,0.156 10 false + 1.385,1.813 1.521,1.969 0.135,0.156 10 false - 1.583,1.708 1.719,1.865 0.135,0.156 10 false 2 2.927,1.625 3.125,1.781 0.198,0.156 10 false 12 0.219,2.323 1.333,2.49 1.115,0.167 10 false Outer Mirror RH 0.167,3.406 2.542,3.583 2.375,0.177 10 false Outer Rear View Mirror Assembly RH 5.885,3.573 7.083,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.198,2.615 2.281,2.927 2.083,0.313 10 false (Outer Rear View Mirror Indicator RH) 2.917,1.344 3.229,1.51 0.313,0.167 10 false z9 2.917,1.823 3.24,2.021 0.323,0.198 10 false z9 3.229,3.396 4.5,3.771 1.271,0.375 10 false Outer Mirror Control ECU Assembly RH 4.01,1.354 4.417,1.51 0.406,0.156 10 false BDSR 4.073,1.823 4.438,1.979 0.365,0.156 10 false GND 4.594,1.146 4.781,1.302 0.188,0.156 10 false 13 4.646,1.625 4.781,1.781 0.135,0.156 10 false 7 4.563,1.354 4.844,1.51 0.281,0.156 10 false H2 4.563,1.833 4.896,1.99 0.333,0.156 10 false H2


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Disconnect the L23 blind spot monitor sensor RH connector.


b.

Disconnect the H2 outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the z9 outer mirror control ECU assembly RH connector.


b.

Disconnect the IND2 outer mirror RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (BSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Disconnect the H2 outer mirror control ECU assembly RH connector.


b.
E233744C43
2.219,0.208 2.646,0.469 0.427,0.26 2.146,1.26 2.365,1.708 false 1.958,1.115 1.667,1.708 false 2.344,0.271 2.625,0.448 0.281,0.177 10 false H2 2.229,1.708 2.708,1.906 0.479,0.198 10 false BDSR 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a 1.49,1.708 1.969,1.906 0.479,0.198 10 false GND
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-13 (BDSR) - H2-7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR RH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

5.INSPECT OUTER MIRROR RH

b.

Inspect the outer rear view mirror indicator RH on the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG