Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109581 REAR CRANKSHAFT OIL SEAL A

2GR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.
A132245C03
2.115,1.156 2.75,1.375 2.75,1.375 2.229,0.635 true 2.125,3.198 2.74,3.042 2.74,3.042 2.094,2.771 false 1.51,2.698 1.188,2.698 false 2.792,1.333 3.229,1.667 0.438,0.333 10 false SST 2.792,2.979 3.219,3.208 0.427,0.229 10 false SST 1,2.604 1.167,2.76 0.167,0.156 10 false *1 1.948,2.375 2.115,2.531 0.167,0.156 10 false *a
*1 Rear Engine Oil Seal Retainer
*a Oil Seal Installation Depth


Apply MP grease to the lip of a new rear engine oil seal.


b.

Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Oil Seal Installation Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap in the rear engine oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using SST, hold the crankshaft pulley.

SST
09213-70011  (09213-70020)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A114342

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A299934C01
1.344,0.198 0.875,0.198 false 2.521,3.344 2.885,3.052 false 0.646,0.115 0.917,0.49 0.271,0.375 10 false *1 2.906,2.958 3.083,3.146 0.177,0.188 10 false *2
*1 Drive Plate and Ring Gear Sub-assembly
*2 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.


e.
A314808C01
1.906,1.198 2.063,0.552 false 2.021,0.354 2.333,0.552 0.313,0.198 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A132243N05
1.875,0.229 2,0.385 0.125,0.156 10 true 1 2.375,0.573 2.5,0.729 0.125,0.156 10 true 7 2.5,0.865 2.625,1.021 0.125,0.156 10 true 4 2.385,1.375 2.51,1.531 0.125,0.156 10 true 6 1.844,1.594 1.969,1.75 0.125,0.156 10 true 2 1.427,1.448 1.552,1.604 0.125,0.156 10 true 8 1.104,0.958 1.229,1.115 0.125,0.156 10 true 3 1.271,0.406 1.396,0.563 0.125,0.156 10 true 5

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 30500 3.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

Hide 30500 4.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for AWD)