Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER HEAD › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109584 CYLINDER HEAD A

2GR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A121839N10
1.688,0.698 2.104,0.094 false 1.729,1.188 1.021,1.427 false 2.146,0 2.479,0.167 0.333,0.167 10 false SST 0.698,1.354 1.031,1.521 0.333,0.167 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A109626

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)


Select a new intake valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the intake valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 intake valve guide bush.

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A120710C04
1.688,0.698 2.24,0.135 2.24,0.135 1.792,1.198 false 2.792,0.865 3.229,0.292 false 2.271,0.031 2.573,0.177 0.302,0.146 10 false SST 3.25,0.188 3.396,0.354 0.146,0.167 10 false *a
*a Protrusion Height


Using SST, tap in a new intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.30 to 9.70 mm (0.3661 to 0.3819 in.)



h.
A131839

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A109628

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)


Select a new exhaust valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 exhaust valve guide bush.

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A120712C04
3.038,1.318 3.343,1.461 0.305,0.143 10 SST 0.029,0.389 0.185,0.549 0.155,0.16 10 *a 0.642,1.326 0.22,0.484 false 2.284,0.543 2.979,1.396 2.979,1.396 2.116,1.125 false
*a Protrusion Height


Using SST, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.30 to 9.70 mm (0.3661 to 0.3819 in.)



h.
A096429

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A131888C03
0.052,0.063 1.313,0.729 1.26,0.667 12 false *A 0.083,1.979 1.552,2.823 1.469,0.844 12 false *B 1.521,3.948 2.531,4.125 1.01,0.177 10 false 2.5 to 3.5 mm
*A for Bank 1
*B for Bank 2


Using a plastic hammer, tap in new ring pins.

Standard Protrusion Height:

2.5 to 3.5 mm (0.0984 to 0.138 in.)



Hide 4.REPLACE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E6 and E8 "TORX" socket wrenches, install the stud bolts.

A319583C01
1.167,1.479 0.802,1.771 0.802,1.771 0.802,1.135 false 6.438,5.031 6.438,5.729 6.438,5.729 6.083,5.385 false 6.417,1.198 5.219,1.688 5.219,1.688 3.969,1.229 false 2.917,3.104 1.729,3.656 1.729,3.656 0.479,3.198 false 5.469,3.385 4.99,3.729 4.99,3.729 4.396,3.396 false 4.99,3.719 4.99,2.708 false 6.417,2.865 6.417,3.708 6.417,3.708 5.896,3.385 false 6.417,3.708 5.917,2.708 false 2.146,5.365 1.688,5.698 1.688,5.698 1.094,5.365 false 1.688,5.688 1.688,4.677 false 3.094,4.865 3.094,5.708 3.094,5.708 2.573,5.385 false 3.083,5.688 2.583,4.688 false 1.531,0.229 1.969,0.51 0.438,0.281 12 false *A 5.063,0.25 5.51,0.635 0.448,0.385 12 false *B 1.563,2.229 2.427,2.625 0.865,0.396 12 false *C 5.344,2.24 5.771,2.594 0.427,0.354 12 false *D 1.813,4.146 2.563,4.76 0.75,0.615 12 false *E 5.458,4.198 5.969,4.656 0.51,0.458 12 false *F 1.406,7.49 1.625,7.708 0.219,0.219 10 false A 4.469,7.49 4.688,7.708 0.219,0.219 10 false B 1.896,6.583 2.5,7.177 0.604,0.594 10 false 20 mm (0.79 in.) 1.906,7.031 2.51,7.688 0.604,0.656 10 false 13 mm (0.51 in.) 2.667,6.885 5.115,7.083 2.448,0.198 10 false 35 mm (1.38 in.) 4.917,6.688 5.531,7.25 0.615,0.563 10 false 16 mm (0.63 in.) 4.948,7.042 5.521,7.823 0.573,0.781 10 false 9 mm (0.35 in.) 5.677,6.938 6.865,7.24 1.188,0.302 10 false 27 mm (1.06 in.) 0.76,1.813 0.979,2.031 0.219,0.219 10 false B 6.417,5.781 6.698,5.979 0.281,0.198 10 false B 5.177,1.729 5.396,1.948 0.219,0.219 10 false A 1.698,3.708 1.917,3.927 0.219,0.219 10 false A 4.948,3.771 5.167,3.99 0.219,0.219 10 false A 6.375,3.76 6.594,3.979 0.219,0.219 10 false A 1.646,5.74 1.865,5.958 0.219,0.219 10 false A 3.073,5.74 3.292,5.958 0.219,0.219 10 false A
*A Bank 1 Rear Side *B Bank 1 Intake Side
*C Bank 2 Intake Side *D Bank 1 Exhaust Side
*E Bank 2 Exhaust Side *F Bank 2 Rear Side


Torque:
Bolt (A) and (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt (C) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 5.REPLACE STRAIGHT PIN

NOTICE:

If a straight pin is deformed, replace it.


a.

Using a plastic hammer, tap in new straight pins as shown in the illustration.

A131890C04
0.115,0 0.875,0.24 0.76,0.24 12 false *A 2.865,0 3.583,0.24 0.719,0.24 12 false *B 4.896,0.906 5.458,1.271 0.563,0.365 10 false 34 mm (1.34 in.) 6.094,0.781 7.125,1.365 1.031,0.583 10 false 17.5 to 19.5 mm
*A for Bank 1 *B for Bank 2


Standard Protrusion Height:

17.5 to 19.5 mm (0.689 to 0.768 in.)