Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109585 CYLINDER BLOCK A

2GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

HINT:

The matchmarks on the connecting rod sub-assembly and connecting rod cap are guides for correct reassembly.



b.
A314948C01
0,0 0,0 false
V100136

Engine Front


Remove the 2 connecting rod cap bolts.


c.
A129761

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower connecting rod bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower connecting rod bearing inserted into the connecting rod cap.



d.
A129720C05
1.885,0.906 0.51,0.604 false 0.281,0.5 0.656,0.813 0.375,0.313 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all of the carbon from the top of the cylinder.


e.

Push the piston, connecting rod sub-assembly and upper connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearing, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the removed parts in the correct order.




Hide 13041 2.REMOVE CONNECTING ROD BEARING

HINT:

Arrange the removed parts in the correct order.


Hide 13011 3.REMOVE PISTON RING SET

a.
A129724C03
0.813,0.552 1.5,0.552 false 0.594,0.469 1,0.823 0.406,0.354 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander and 2 side rails by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 4.REMOVE PISTON

a.
A129725

Check the fitting condition between the piston and piston pin.

i.

Try to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston and piston pin as a set.



b.
A129726

Remove the connecting rod sub-assembly from the piston.

i.

Using a screwdriver, pry off the piston pin hole snap rings from the piston.


ii.
A109729

Gradually heat the piston to approximately 80°C (176°F).

CAUTION:

Be sure to wear protective gloves.



iii.
A194887

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in the correct order.





c.
A129729

Using a gasket scraper, remove any carbon from the piston top.

NOTICE:

Be careful not to scratch a piston.



d.
A129730

Using a groove cleaning tool or a broken ring, clean the piston ring grooves.


e.
A129731

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13411 5.REMOVE CRANKSHAFT

a.
A314821N01
0.208,0.969 0.323,1.146 0.115,0.177 10 false 6 0.802,0.479 0.917,0.656 0.115,0.177 10 true 7 1.208,0.24 1.323,0.417 0.115,0.177 10 true 8 2.021,1.948 2.135,2.125 0.115,0.177 10 true 1 3.302,1.021 3.417,1.198 0.115,0.177 10 false 2 2.51,1.51 2.625,1.688 0.115,0.177 10 true 4 2.927,1.198 3.042,1.375 0.115,0.177 10 true 3 1.51,0.01 1.625,0.188 0.115,0.177 10 true 5

Uniformly loosen and remove the 8 crankshaft bearing cap set bolts and 8 seal washers in several steps in the order shown in the illustration.


b.
A134892N02
0.385,1.51 0.5,1.708 0.115,0.198 10 true 1 0.375,0.25 0.594,0.448 0.219,0.198 10 true 2 3.01,1.521 3.167,1.729 0.156,0.208 10 false 3 3.042,0.281 3.208,0.448 0.167,0.167 10 false 4 1.01,1.49 1.125,1.698 0.115,0.208 10 true 5 1.01,0.24 1.135,0.417 0.125,0.177 10 true 6 2.396,1.521 2.563,1.667 0.167,0.146 10 true 7 2.417,0.271 2.531,0.448 0.115,0.177 10 true 8 0.333,1.021 0.458,1.229 0.125,0.208 10 true 9 0.24,0.688 0.417,0.875 0.177,0.188 10 false 10 3.042,1.021 3.354,1.24 0.313,0.219 10 false 11 3.052,0.698 3.25,0.906 0.198,0.208 10 false 12 0.927,1.021 1.094,1.229 0.167,0.208 10 true 13 0.906,0.698 1.073,0.896 0.167,0.198 10 true 14 2.427,1.01 2.604,1.188 0.177,0.177 10 true 15 2.417,0.698 2.583,0.885 0.167,0.188 10 true 16

Uniformly loosen the 16 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


c.
A122567C12
1.802,1.521 2.615,2.198 true 0.521,2.427 0.948,2.781 false 1.719,2.865 2.01,2.563 false 1.271,3.719 0.885,4.156 0.885,4.156 1.563,3.969 false 0.688,4.104 0.865,4.302 0.177,0.198 10 false *b 2.604,2.219 2.792,2.417 0.188,0.198 10 false *a 2.104,2.427 2.646,2.979 0.542,0.552 10 false *2 0.281,2.323 0.625,2.594 0.344,0.271 10 false *1
*1 Cylinder Block Sub-Assembly
*2 Crankshaft Bearing Cap
*a Protective Tape
*b Joint Surface


Using a screwdriver, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.

NOTICE:
·

Push up the crankshaft bearing cap slowly and evenly, alternating from the right and left side so that the crankshaft bearing cap can be removed.

·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and the crankshaft bearing cap.



HINT:

Tape the screwdriver tip before use.



d.

Remove the crankshaft.


Hide 11711 6.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearings and lower crankshaft bearings.

HINT:

Arrange the removed parts in the correct order.



Hide 11011 7.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A109726

Remove the crankshaft thrust washer set from the cylinder block sub-assembly.


Hide 15708 8.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies.


b.

Check the 3 No. 1 oil nozzle sub-assemblies for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.


Hide 11401 9.CLEAN CYLINDER BLOCK SUB-ASSEMBLY