Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109585 CYLINDER BLOCK A

2GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston and piston ring set.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon wrench, install the 3 No. 1 oil nozzle sub-assemblies with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13101 2.INSTALL PISTON

a.
A131876C03
2.292,1.583 1.625,1.802 false 1.417,1.729 1.698,1.969 0.281,0.24 10 false *a
*a Cutout


Using a screwdriver, install a new piston pin hole snap ring at one end of the piston pin hole.

HINT:

Confirm that the end gap of the snap ring is not aligned with the cutout of the piston pin hole.



b.
A125895

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.

CAUTION:

Be sure to wear protective gloves.



d.
A131878C03
0.148,0.305 0.303,0.453 0.155,0.148 10 *a 2.277,0.399 0.355,0.399 0.355,0.399 1.077,1.262 false
*a Front Mark


Align the front marks of the piston and connecting rod sub-assembly, and push in the piston pin with your thumb.

HINT:

The piston and piston pin are a matched set.



e.
A107551

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A131879C03
2.25,1.635 2.021,1.51 false 1.844,1.427 2.469,1.792 0.625,0.365 10 false *a
*a Cutout


Using a screwdriver, install a new piston pin hole snap ring at the other end of the piston pin hole.

HINT:
·

Confirm that the end gap of the snap ring is not aligned with the cutout of the piston pin hole.

·

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13011 3.INSTALL PISTON RING SET

a.

Install the oil ring expander and 2 side rails by hand.


b.
A131880C03
2.552,3.521 2.104,3.219 false 2.927,3.406 2.646,2.948 false 2.719,3.885 2.469,4.115 false 1.625,0.417 0.979,0.26 false 2.25,3.833 2,3.729 false 0.792,0.167 1.271,0.542 0.479,0.375 10 false *a 0.427,3.802 0.906,4.167 0.479,0.365 10 false *1 1.552,3.802 2.094,4.26 0.542,0.458 10 false *2 2.833,3.927 3.125,4.188 0.292,0.26 10 false *3 1.927,3.104 2.365,3.583 0.438,0.479 10 false *c 2.302,4.083 2.844,4.458 0.542,0.375 10 false *d 2.5,2.802 2.938,3.094 0.438,0.292 10 false *b 2.292,3.781 2.604,3.979 0.313,0.198 10 false *e
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring
*a Piston Ring Expander
*b Upper Side Rail
*c Oil Ring Expander
*d Lower Side Rail
*e Cutout


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.

NOTICE:
·

The No. 1 compression ring can be installed with either side facing upward.

·

Install the No. 2 compression ring with the cutout facing downward.




c.
A131881C07
1.24,1.698 0.688,1.292 false 1.625,2.667 2.396,3.323 0.771,0.656 10 false *d 1.625,0.604 2.063,0.906 0.438,0.302 10 false *b 0.927,2.354 1.521,2.938 0.594,0.583 10 false *1 0.927,0.927 1.479,1.333 0.552,0.406 10 false *2 0.469,1.188 0.625,1.354 0.156,0.167 10 false *a 0.604,1.656 1.406,2.156 0.802,0.5 10 false *c
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Front Mark
*b Lower Side Rail
*c Oil Ring Expander
*d Upper Side Rail


Position the piston ring set so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.


HINT:

Perform "Inspection After Repair" after replacing the piston ring.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.
A124282C07
0.781,0.427 1.156,0.75 0.375,0.323 10 false *a 2.552,0.427 2.896,0.781 0.344,0.354 10 false *b 0.5,2.563 1.188,2.771 0.688,0.208 10 false 21.0 mm 2.354,2.563 3.042,2.771 0.688,0.208 10 false 18.0 mm
*a No. 1 and No. 4 Crankshaft Bearing
*b No. 2 and No. 3 Crankshaft Bearing


Clean the main journals and both surfaces of the crankshaft bearings.

NOTICE:

Crankshaft bearings come in widths of 18.0 mm (0.709 in.) and 21.0 mm (0.827 in.). Install the 21.0 mm (0.827 in.) crankshaft bearings to the No. 1 and No. 4 cylinder block journal positions. Install the 18.0 mm (0.709 in.) crankshaft bearings to the No. 2 and No. 3 positions.



b.
A314949C01
1.74,2.927 2.74,2.073 2.74,2.073 2.635,2.948 false 2.75,1.906 3.063,2.104 0.313,0.198 10 false *a 1.667,3.781 1.979,3.979 0.313,0.198 10 false *b 2.688,3.781 3,3.979 0.313,0.198 10 false *c
*a Upper Crankshaft Bearing
*b Correct
*c Incorrect


Install the upper crankshaft bearing.

i.

Install the upper crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the crankshaft bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.





c.
A131826C04
1.042,1.938 0.771,2.083 false 2.448,2.677 2.104,2.177 false 0.583,2.052 1.115,2.427 0.531,0.375 10 false *b 1.927,2.031 2.385,2.344 0.458,0.313 10 false *a 0.969,2.938 1.094,3.229 0.125,0.292 10 false A 2.302,2.938 2.427,3.229 0.125,0.292 10 false B
*a Vernier Caliper
*b Mark 1, 2, 3, 4 or 5


Install the lower crankshaft bearing.

i.

Install the lower crankshaft bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the lower crankshaft bearing edge.

Difference Between (A) and (B):

0.7 mm (0.0276 in.) or less


NOTICE:
·

Do not apply engine oil to the crankshaft bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.





Hide 11011 5.INSTALL CRANKSHAFT THRUST WASHER SET

a.

Apply engine oil to the crankshaft thrust washer set.


b.
A106233C05
1.104,1.25 2.271,0.302 2.271,0.302 1.938,1.49 false 2.313,0.146 2.49,0.354 0.177,0.208 10 false *a
*a Oil Grooves


Install the crankshaft thrust washer set under the No. 2 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the crankshaft bearings, then place the crankshaft on the cylinder block sub-assembly.


b.
A121711C07
0.865,1.333 0.865,0.26 false 2.771,1.323 2.771,0.25 2.771,0.25 0.615,0.25 false 2.135,1.323 2.135,0.25 false 1.531,1.302 1.531,0.25 false 0.896,2.76 0.896,3.052 false 2.802,2.76 2.802,2.917 2.802,2.917 0.896,2.917 false 1.552,2.76 1.552,2.917 false 2.146,2.76 2.146,2.917 false 0.417,0.167 1.042,0.594 0.625,0.427 10 false *a 0.813,3.063 1.219,3.365 0.406,0.302 10 false *b
*a Projection
*b Number Mark


Confirm the projections and numbers on the crankshaft bearing caps and install the 4 crankshaft bearing caps on the cylinder block sub-assembly.

HINT:

A number is marked on each crankshaft bearing cap to indicate the installation position.



c.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.


d.

Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.


e.
A134893C04
1.094,2.125 0.354,2.865 false 1.594,3.719 1.76,3.906 0.167,0.188 10 false *b 0.167,2.823 0.344,2.979 0.177,0.156 10 false *a
*a Less than 6 mm
*b Bolt Length 100 to 102 mm


Push the crankshaft bearing cap with your hand until the clearance between the crankshaft bearing cap and the cylinder block sub-assembly is less than 6 mm (0.236 in.) by using the 2 inside crankshaft bearing cap bolts as a guide.

Bolt Length:

100 to 102 mm (3.94 to 4.02 in.)



f.
A131829

Using a plastic hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 8 crankshaft bearing cap bolts.


h.
A134894C03
1.613,3.776 1.785,3.931 0.172,0.155 10 *a
*a Bolt Length


Temporarily install the 8 crankshaft bearing cap bolts to the outside positions.

Bolt Length:

105.5 to 107.5 mm (4.15 to 4.23 in.)



i.

Install the crankshaft bearing cap bolts.

HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



j.

Step 1:

i.
A134892N03
2.438,0.99 2.563,1.177 0.125,0.188 10 true 2 0.99,0.677 1.094,0.854 0.104,0.177 10 true 3 0.99,1.01 1.104,1.177 0.115,0.167 10 true 4 3.063,0.719 3.219,0.906 0.156,0.188 10 false 5 3.073,1.021 3.229,1.229 0.156,0.208 10 false 6 0.323,0.656 0.427,0.833 0.104,0.177 10 false 7 0.333,0.99 0.458,1.156 0.125,0.167 10 true 8 2.406,0.25 2.51,0.427 0.104,0.177 10 true 9 2.375,1.458 2.563,1.635 0.188,0.177 10 true 10 0.958,0.229 1.125,0.417 0.167,0.188 10 true 11 0.938,1.469 1.125,1.646 0.188,0.177 10 true 12 3.01,0.26 3.24,0.448 0.229,0.188 10 false 13 3.01,1.469 3.24,1.656 0.229,0.188 10 false 14 0.292,0.198 0.51,0.417 0.219,0.219 10 false 15 0.302,1.479 0.49,1.646 0.188,0.167 10 true 16 2.427,0.646 2.531,0.802 0.104,0.156 10 true 1

Uniformly tighten the 16 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)

If any of the crankshaft bearing cap bolts does not meet the specified torque, replace it.



k.

Step 2:

i.
A314822C01
2.229,0.531 2.594,0.26 false 2.635,0.135 2.948,0.333 0.313,0.198 10 false *a 1.323,0.292 1.635,0.49 0.313,0.198 10 false *b
*a Paint Mark
*b Turn 90°
V100136

Engine Front


Mark the front of the crankshaft bearing cap bolts with paint.


ii.

Tighten the crankshaft bearing cap bolts by 90° in the order shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



l.
A314821N02
2.917,0.781 3.021,0.177 3.021,0.177 2,0.344 false 0.208,0.969 0.323,1.146 0.115,0.177 10 false 3 0.802,0.479 0.917,0.656 0.115,0.177 10 true 2 1.208,0.24 1.323,0.417 0.115,0.177 10 true 1 2.021,1.948 2.135,2.125 0.115,0.177 10 true 8 3.302,1.021 3.417,1.198 0.115,0.177 10 false 7 2.51,1.51 2.625,1.688 0.115,0.177 10 true 5 2.927,1.198 3.042,1.375 0.115,0.177 10 true 6 1.51,0.01 1.625,0.188 0.115,0.177 10 true 4 3.104,0.073 3.219,0.25 0.115,0.177 10 false A

Install 8 new seal washers and uniformly tighten the 8 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
51.5 N*m (525 kgf*cm, 38 ft.*lbf)

Bolt Length:
Item Length
Bolt (A) 45 mm (1.77 in.)
Except bolt (A) 30 mm (1.18 in.)



m.

Check that the crankshaft turns smoothly.


n.

Check the crankshaft thrust clearance.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearings to the connecting rod sub-assembly and connecting rod cap.


b.
A314950C01
0.792,3.677 0.542,3.281 false 0.385,3.135 0.698,3.333 0.313,0.198 10 false *a 2.031,3.354 2.167,3.552 0.135,0.198 10 false A 3.104,3.354 3.24,3.552 0.135,0.198 10 false B
*a Vernier Caliper


Using a vernier caliper, measure the distance between the connecting rod sub-assembly and connecting rod cap edges and the connecting rod bearing edge.

Difference Between (A) and (B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the connecting rod bearings and the contact surfaces.



Hide 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A131881C07
1.24,1.698 0.688,1.292 false 1.625,2.667 2.396,3.323 0.771,0.656 10 false *d 1.625,0.604 2.063,0.906 0.438,0.302 10 false *b 0.927,2.354 1.521,2.938 0.594,0.583 10 false *1 0.927,0.927 1.479,1.333 0.552,0.406 10 false *2 0.469,1.188 0.625,1.354 0.156,0.167 10 false *a 0.604,1.656 1.406,2.156 0.802,0.5 10 false *c
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Front Mark
*b Lower Side Rail
*c Oil Ring Expander
*d Upper Side Rail


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.
A131886C04
1.313,2.927 1.885,3.031 1.885,3.031 2.542,2.542 false 1.823,3.083 1.979,3.24 0.156,0.156 10 false *a
*a Front Mark
V100136

Engine Front


Using a piston ring compressor, push the correctly matched piston and connecting rod sub-assembly into the cylinder with the front mark of the piston facing the front.

NOTICE:

Match the connecting rod cap with the connecting rod sub-assembly.



d.
A314948C02
0.615,1.677 1.74,1.177 false 0.438,1.615 0.75,1.813 0.313,0.198 10 false *a
*a Front Mark
V100136

Engine Front


Check that the front mark of the connecting rod cap is facing the front.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Install the 2 connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A131887

Alternately tighten the 2 connecting rod cap bolts in several steps.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



h.
A101478C52
1.233,0.404 1.384,0.585 0.152,0.182 10 *b 2.085,0.747 2.575,0.475 false 2.623,0.372 2.824,0.528 0.201,0.157 10 *a
*a Paint Mark
*b Turn 90°
V100136

Engine Front


Step 2:

i.

Mark the front of each connecting rod cap bolt with paint.


ii.

Further tighten the connecting rod cap bolts by 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Confirm that the crankshaft turns smoothly.


j.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION