Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109593 REAR CRANKSHAFT OIL SEAL A

1AR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before service.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




c.
A195810N12
1.833,1.292 2.042,1.698 2.042,1.698 2.135,1.698 true 1.302,1.396 2.042,1.698 true 2.167,1.625 2.573,1.802 0.406,0.177 10 true SST

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the edges of the cylinder block sub-assembly and stiffening crankcase assembly.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap in the rear engine oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A195875N17
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
91551-80650  

HINT:

SST (crankshaft pulley holding tool) fixing bolt part No.: 91551-80650 (2 pcs)



b.

Clean the 8 bolts and the bolt holes.


c.
A196850

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A196851C07
2.389,0.991 2.57,1.155 0.181,0.164 10 *2 2.372,0.953 2.218,0.66 false 1.895,2.025 2.076,2.189 0.181,0.164 10 *1 1.878,1.987 1.724,1.695 false
*1 Drive Plate and Ring Gear Sub-assembly
*2 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and ring gear sub-assembly and rear drive plate spacer onto the crankshaft.


e.
A192239C77
1.573,0.76 1.677,0.76 1.677,0.76 1.823,1.24 false 1.375,0.677 1.573,0.833 0.198,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A196849N04
1.938,0.333 2.031,0.49 0.094,0.156 10 true 1 1.938,1.729 2.031,1.906 0.094,0.177 10 true 2 1.281,1.042 1.396,1.188 0.115,0.146 10 true 3 2.677,1.031 2.771,1.188 0.094,0.156 10 true 4 1.49,0.531 1.604,0.677 0.115,0.146 10 true 5 2.469,1.51 2.583,1.667 0.115,0.156 10 true 6 2.469,0.531 2.594,0.688 0.125,0.156 10 true 7 1.51,1.542 1.677,1.698 0.167,0.156 10 true 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.