Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109596 CYLINDER HEAD A

1AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly approximately to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A194970
0.109,0.36 0.404,0.523 0.295,0.163 10 SST 0.957,0.654 0.473,0.446 0.473,0.446 1.087,1.105 false

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194985

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a new intake valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the intake valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 intake valve guide bush.

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A194972
1.01,0.813 0.385,0.427 0.385,0.427 1.24,1.323 true 2.448,0.542 2.604,0.688 0.156,0.146 10 false *a 0.021,0.344 0.323,0.49 0.302,0.146 10 false SST
*a Height


Using SST and a hammer, tap in the selected intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.8 to 15.2 mm (0.583 to 0.598 in.)



g.
A194973

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A281402
0.398,0.229 0.735,0.398 0.337,0.168 10 SST 1.206,0.671 0.756,0.319 0.756,0.319 1.148,1.168 false

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194975

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a new exhaust valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 in 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 exhaust valve guide bush.

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A281345
2.878,1.627 3.065,1.793 0.186,0.166 10 *a 0.295,0.191 0.613,0.349 0.318,0.158 10 SST 1.221,0.611 0.668,0.28 0.668,0.28 1.159,1.119 false
*a Height


Using SST and a hammer, tap in the selected exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.2 to 14.6 mm (0.559 to 0.575 in.)



g.
A281346

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11115A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 2 ring pins.


b.
A194963
2.267,2.302 3.138,2.479 0.872,0.177 10 6.5 to 7.5 mm

Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)