Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109596 CYLINDER HEAD A

1AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11193 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A289330N01
1.635,0.208 2.51,0.385 0.875,0.177 10 false 1.0 to 3.0 mm 1.063,1.76 2.302,2.115 1.24,0.354 10 false 1.0 to 3.0 mm (0.0394 to 0.118 in.)

Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Do not expose the spark plug tube to engine oil for at least 1 hour after installing it.




b.
A194971C12
3.042,3.542 2.927,3.542 2.927,3.542 2.292,3.708 true 2.396,3.052 2.99,3.229 0.594,0.177 10 false 112 mm 3.125,3.458 3.292,3.625 0.167,0.167 10 false *a
*a Cylinder Head Casting Surface


Using a wooden block and hammer, tap in the spark plug tube.

Standard Protrusion Height:

112 mm (4.41 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 17159 2.INSTALL CYLINDER HEAD STUD BOLT

a.
A194964N12
1.552,1.781 1.427,1.781 1.427,1.781 1.094,2.219 false 1.958,2.292 1.833,2.292 1.833,2.292 1.552,2.438 false 1.063,3.021 0.917,3.021 0.917,3.021 1.094,2.698 false 1.594,1.688 2.844,1.844 1.25,0.156 10 18 mm (0.708 in.) 1.115,2.927 2.344,3.115 1.229,0.188 10 13 mm (0.512 in.) 2.021,2.208 3.292,2.427 1.271,0.219 10 33 mm (1.299 in.)

Using an E7 "TORX" socket wrench, install the 5 cylinder head stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A194960

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11117F 4.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A194961

Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seat to the cylinder head sub-assembly.


Hide 13741A 6.INSTALL VALVE STEM OIL SEAL

a.
A124785C15
1.01,0.813 1.469,0.969 false 2.5,0.813 2.063,0.969 false 0.719,0.063 0.896,0.24 0.177,0.177 10 false *a 2.656,0.052 2.865,0.229 0.208,0.177 10 false *b 1.875,0.885 2.031,1.031 0.156,0.146 10 false *d 1.51,0.875 1.667,1.031 0.156,0.156 10 false *c
*a Intake Valve Stem Oil Seal
*b Exhaust Valve Stem Oil Seal
*c Gray
*d Black


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay attention when installing the valve stem oil seals. For example, installing an intake valve stem oil seal onto the exhaust side or installing an exhaust valve stem oil seal onto the intake side can cause installation problems later.


HINT:

The intake valve stem oil seals are gray and the exhaust valve stem oil seals are black.



b.
A194977C10
0.908,1.919 1.103,2.075 0.195,0.156 10 *a 2.209,1.919 2.399,2.08 0.19,0.161 10 *b 1.23,0.0020 1.534,0.154 0.304,0.152 10 SST 1.591,0.088 1.752,0.088 1.752,0.088 2.008,0.665 false
*a Correct
*b Incorrect


Using SST, push in the valve stem oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the valve stem seal to be damaged or improperly seated.



Hide 13711 7.INSTALL INTAKE VALVE

a.
A285332C18
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.

Install the intake valve, compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A194956E01
3.084,0 3.414,0.149 0.330,0.149 10 SST 3.084,0 3.414,0.149 0.330,0.149 10 SST 2.787,0 2.916,0 2.916,0 3.414,0.414 false 3.14,0 3.228,0 3.228,0 3.414,0.07 false

Using SST and wooden blocks, compress the compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.
A194979

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve spring retainer.



Hide 13715 8.INSTALL EXHAUST VALVE

a.
A285332C19
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Install the exhaust valve, compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A194957E01
3.099,0 3.414,0.146 0.314,0.146 10 SST 3.414,0 3.276,0 3.276,0 3.175,0.591 false 3.099,0 3.414,0.146 0.314,0.146 10 SST 3.414,1.252 3.414,1.131 3.414,1.131 3.231,0 false

Using SST and wooden blocks, compress the compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.
A194981

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve spring retainer.