Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109597 CYLINDER BLOCK A

1AR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A259168

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.160 to 0.512 mm (0.00630 to 0.0202 in.)


Maximum Thrust Clearance:

0.512 mm (0.0202 in.)


If the thrust clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A259169C05
0.131,1.347 0.324,1.532 0.193,0.185 10 *a 0.628,0.793 0.213,1.208 0.213,1.208 0.213,1.347 false
*a Alignment Mark


Check the alignment marks on the connecting rod sub-assembly and connecting rod cap to ensure correct reassembly.


b.
A259170

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.


e.
A259171C05
1.51,1.167 0.76,0.875 0.76,0.875 0.646,0.875 false 0.438,0.802 0.615,0.979 0.177,0.177 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A259172C09
0.535,0.319 0.731,0.501 0.196,0.182 10 *a 1.459,0.904 0.876,0.42 0.876,0.42 0.737,0.42 false
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction, and install the connecting rod cap.


g.
A259170

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Install and alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


i.
A101478C50
2.063,0.76 2.333,0.177 2.333,0.177 2.479,0.177 false 1.146,0.385 1.469,0.594 0.323,0.208 10 false 90° 2.49,0.083 2.698,0.281 0.208,0.198 10 false *a
*a Paint Mark
V100136

Engine Front


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts by 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A259173C05
1.167,0.948 1,0.458 1,0.458 0.917,0.458 false 1.479,3.188 0.719,3.667 0.719,3.667 1.229,4.177 false 1.479,3.469 0.719,3.667 false 0.729,0.365 0.938,0.594 0.208,0.229 10 false *a 0.51,3.573 0.719,3.802 0.208,0.229 10 false *b
*a Plastigage
*b Number Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.030 to 0.063 mm (0.00118 to 0.00248 in.) or 0.033 to 0.063 mm (0.00130 to 0.00248 in.)


Maximum Oil Clearance:

0.07 mm (0.00276 in.)


NOTICE:

Remove the Plastigage completely after the measurement.


If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

HINT:

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.


Standard Crank Pin Diameter:

51.492 to 51.500 mm (2.0272 to 2.0276 in.)


Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 54.500 to 54.508 mm (2.1457 to 2.1460 in.)
2 54.509 to 54.516 mm (2.1460 to 2.1463 in.)
3 54.517 to 54.524 mm (2.1463 to 2.1466 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.483 to 1.487 mm (0.0584 to 0.0585 in.)
2 1.488 to 1.491 mm (0.0586 to 0.0587 in.)
3 1.492 to 1.495 mm (0.0587 to 0.0589 in.)



m.

Perform the inspection for each cylinder.


Hide 3.REMOVE PISTON WITH CONNECTING ROD

a.
A194883C01
1.198,0.948 2.333,0.594 2.333,0.594 2.5,0.594 false 2.573,0.5 2.885,0.698 0.313,0.198 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.


c.

Push the piston with connecting rod and connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the removed parts in the correct order.

·

Be sure to arrange the removed piston and connecting rod sub-assemblies in such a way that they can be reinstalled exactly as before.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rod sub-assemblies and connecting rod caps.

HINT:

Arrange the removed parts in the correct order.



Hide 5.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A259174

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Maximum Thrust Clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.

Standard Thrust Washer Thickness:

1.93 to 1.98 mm (0.0760 to 0.0780 in.)



Hide 13411 6.REMOVE CRANKSHAFT

a.
A259176N03
3.094,1.531 3.229,1.729 0.135,0.198 10 false 1 3.125,0.521 3.26,0.719 0.135,0.198 10 false 2 0.396,1.51 0.531,1.708 0.135,0.198 10 false 3 0.396,0.51 0.531,0.708 0.135,0.198 10 false 4 2.448,1.615 2.583,1.813 0.135,0.198 10 true 5 2.448,0.427 2.583,0.625 0.135,0.198 10 true 6 1.031,1.615 1.167,1.813 0.135,0.198 10 true 7 1.042,0.427 1.177,0.625 0.135,0.198 10 true 8 1.74,1.615 1.875,1.813 0.135,0.198 10 true 9 1.677,0.427 1.917,0.625 0.24,0.198 10 true 10

Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.


b.

Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in the correct order.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.


Hide 11791 7.REMOVE CRANKSHAFT THRUST WASHER

a.
A195787

Remove the crankshaft thrust washers from the cylinder block sub-assembly.


Hide 11711 8.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings and No. 2 crankshaft bearings from the cylinder block sub-assembly and crankshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13471A 9.REMOVE CRANKSHAFT PULLEY KEY

a.

Using a screwdriver, remove the 2 crankshaft pulley keys from the crankshaft.


Hide 13011 10.REMOVE PISTON RING SET

a.
A194884C11
1.052,1.75 1.052,1.646 false 1.052,1.646 1.354,1.313 false 0.979,1.75 1.156,1.906 0.177,0.156 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring and oil ring expander by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101A 11.REMOVE PISTON PIN HOLE SNAP RING

a.
A194885C11
1.448,0.99 1.177,0.25 1.177,0.25 1.094,0.25 false 1.635,1.094 1.083,1.563 1.083,1.563 0.917,1.563 false 0.906,0.167 1.063,0.323 0.156,0.156 10 false *a 0.719,1.469 0.906,1.625 0.188,0.156 10 false *b
*a Protective Tape
*b Cutout


Using a screwdriver, pry out the piston pin hole snap ring (front side).

NOTICE:

Do not remove the snap ring (rear side) unless necessary.


HINT:

Tape the screwdriver tip before use.



Hide 13211 12.REMOVE PISTON

a.
A194886

Gradually heat each piston to 80 to 90°C (176 to 194°F).


b.
A194887

Using a hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Be sure to arrange the removed pistons, piston pins, piston rings, connecting rod sub-assemblies and connecting rod bearings in such a way that they can be reinstalled exactly as before.

·

Arrange the removed parts in the correct order.




Hide 15708 13.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A195788

Using a 5 mm hexagon wrench, remove the 2 bolts and 2 No. 1 oil nozzle sub-assemblies.


Hide 15709 14.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A195789

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 2 oil nozzle sub-assemblies.


Hide 15.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.