Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109597 CYLINDER BLOCK A

1AR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston or piston ring.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL CYLINDER HEAD STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E8 and E10 "TORX" socket wrenches, install the stud bolts.

A198174C08
5,0.167 4.677,0.458 true 4.677,0.781 4.99,0.979 true 4.99,1.24 4.667,1.448 true 4.688,2.25 5,2.479 true 0.219,1.448 0.396,1.615 0.177,0.167 10 false *b 0.219,0.052 0.396,0.219 0.177,0.167 10 false *a 1.438,1.198 1.552,1.354 0.115,0.156 10 true A 2.5,1.208 2.615,1.365 0.115,0.156 10 true A 3.875,0.063 3.99,0.219 0.115,0.156 10 false A 1.896,2.208 2.042,2.354 0.146,0.146 10 true B 3.875,1.073 4.021,1.219 0.146,0.146 10 false B 5.031,0.083 6.271,0.271 1.24,0.188 10 false 16 mm (0.630 in.) 5.031,0.906 6.521,1.104 1.49,0.198 10 false 12 mm (0.472 in.) 5.031,2.427 6.156,2.594 1.125,0.167 10 false 12 mm (0.472 in.) 5.031,1.146 6.156,1.313 1.125,0.167 10 false 46 mm (1.81 in.) 4.969,1.74 6.094,1.906 1.125,0.167 10 false 67 mm (2.64 in.) 4.969,0.542 6.135,0.74 1.167,0.198 10 false 34 mm (1.34 in.)
*a RH Side *b LH Side


Torque:
Stud Bolt (A) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Stud Bolt (B) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 15709 2.INSTALL NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A195789

Using a 5 mm hexagon wrench, install the 4 No. 2 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A195788

Using a 5 mm hexagon wrench, install the 2 No. 1 oil nozzle sub-assemblies with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13211 4.INSTALL PISTON

a.

Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.


b.

Gradually heat the piston to 80 to 90°C (176 to 194°F).


c.

Coat the piston, piston pin and connecting rod sub-assembly with engine oil.


d.
A285365C08
0.802,1.219 0.635,0.427 0.635,0.427 0.781,0.427 false 1.073,2.49 0.677,2.042 0.677,2.042 0.531,2.042 false 3.031,1.313 2.875,1.313 2.875,1.313 2.438,0.51 false 0.833,0.333 1.146,0.49 0.313,0.156 10 false *a 0.365,1.948 0.677,2.104 0.313,0.156 10 false *b 3.115,1.219 3.427,1.375 0.313,0.156 10 false *b
*a Cutout
*b Front Mark


Align the cutout of the piston and front mark of the connecting rod sub-assembly, insert the connecting rod sub-assembly into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the snap ring.

HINT:

The piston and piston pin are a matched set.



e.
A195811C13
1.26,1.885 0.875,1.885 false 2.146,1.698 1.76,1.698 false 0.667,1.781 0.844,1.948 0.177,0.167 10 false *a 2.198,1.615 2.375,1.781 0.177,0.167 10 false *1
*1 Piston Pin Hole Snap Ring
*a Cutout


Using a screwdriver, install a new piston pin hole snap ring (front side) on the other side of the piston pin hole.

HINT:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the cutout of the piston.



f.
A195813

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod sub-assembly back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and piston pin as a set.


ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and piston pin as a set.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13011 5.INSTALL PISTON RING SET

a.
A308268C03
1.615,2.938 1.698,3.115 1.698,3.115 1.771,2.948 false 2.021,0.448 2.177,0.229 2.177,0.229 2.313,0.229 false 1.688,1.948 1.688,1.573 false 1.813,0.646 2.167,1.104 2.167,1.104 2.344,1.104 false 2.354,0.177 2.667,0.333 0.313,0.156 10 false *1 2.417,1.021 2.729,1.177 0.313,0.156 10 false *2 1.625,1.958 1.938,2.115 0.313,0.156 10 false *a 1.635,3.135 1.948,3.292 0.313,0.156 10 false *b
*1 Oil Ring
*2 Oil Ring Expander
*a Coil Joint
*b Oil Ring End


Install the oil ring expander and oil ring by hand.

HINT:

Arrange the oil ring ends and coil joint as shown in the illustration.



b.
A297342C08
1.49,3.146 1.885,3.271 1.885,3.271 2.063,3.271 true 1.49,2.385 2.052,2.219 2.052,2.219 2.198,2.219 true 1.5,2.979 2.052,2.865 2.052,2.865 2.198,2.865 true 1.479,2.552 2.167,2.552 false 0.719,2.677 0.531,2.427 0.531,2.427 0.354,2.427 true 0.719,3.313 0.552,3.094 0.552,3.094 0.375,3.094 true 0.99,4.333 0.99,4.156 false 2.063,4.333 2.063,4.156 false 2.146,0.573 2.49,0.281 2.49,0.281 2.635,0.281 false 2.24,2.125 2.438,2.302 0.198,0.177 10 *4 0.177,2.323 0.375,2.5 0.198,0.177 10 *1 0.198,2.99 0.396,3.167 0.198,0.177 10 *2 2,4.365 2.198,4.542 0.198,0.177 10 *2 0.917,4.354 1.115,4.531 0.198,0.177 10 *1 2.229,2.75 2.427,2.927 0.198,0.177 10 *5 2.094,3.177 2.292,3.354 0.198,0.177 10 *6 2.208,2.438 2.406,2.615 0.198,0.177 10 *6 2.688,0.188 2.885,0.365 0.198,0.177 10 *3
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Piston Ring Expander
*b Code Mark (N1)
*c Code Mark (N2)
*d Paint Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.

Piston Ring Mark:
Item Code Mark
No. 1 Compression Ring N1
No. 2 Compression Ring N2


NOTICE:

Install the compression rings with the code marks facing upward.


HINT:

Perform "Inspection After Repair" after replacing the piston, piston ring.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13471A 6.INSTALL CRANKSHAFT PULLEY KEY

a.

Install the 2 crankshaft pulley keys to the crankshaft.


Hide 11711 7.INSTALL CRANKSHAFT BEARING

a.
A195816C12
1.614,3.832 1.787,3.984 0.173,0.151 10 *a 2.638,3.832 2.812,3.991 0.173,0.159 10 *b
*a Correct
*b Incorrect


Clean the main journal and both surfaces of the crankshaft bearing and No. 2 crankshaft bearing.


b.

Install the crankshaft bearing to the cylinder block sub-assembly as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the crankshaft bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.




c.
A195817C14
2.333,3.219 1.948,2.573 1.948,2.573 1.802,2.573 false 0.552,3.729 0.76,3.958 0.208,0.229 10 false A 2.219,3.708 2.427,3.938 0.208,0.229 10 false B 1.604,2.49 1.771,2.635 0.167,0.146 10 false *a
*a Vernier Caliper


Install the No. 2 crankshaft bearing onto the crankshaft bearing cap.


d.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the No. 2 crankshaft bearing edge.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the crankshaft bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.




Hide 11791 8.INSTALL CRANKSHAFT THRUST WASHER

a.
A195787C12
1.031,0.219 1.167,0.219 false 1.167,0.219 1.427,1.281 false 1.156,0.219 2.021,1.542 false 0.865,0.135 1.042,0.292 0.177,0.156 10 false *a
*a Oil Groove


Apply engine oil to the crankshaft thrust washers.


b.

Install the 2 crankshaft thrust washers onto the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 9.INSTALL CRANKSHAFT

a.
A259179C06
2.073,2.74 2.865,2.74 false 2.906,2.656 3.094,2.885 0.188,0.229 10 false *a
*a Front Mark


Apply engine oil to the crankshaft bearing, and place the crankshaft on the cylinder block sub-assembly.


b.

Confirm the front marks and numbers, and install the crankshaft bearing caps onto the cylinder block sub-assembly with the front marks as shown in the illustration.

HINT:

The crankshaft bearing cap bolts are tightened in 3 progressive steps.



c.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.


d.

Step 1:

i.
A259176N07
2.479,0.479 2.615,0.677 0.135,0.198 10 true 5 2.448,1.604 2.583,1.802 0.135,0.198 10 true 6 0.396,0.51 0.531,0.708 0.135,0.198 10 false 7 0.396,1.5 0.531,1.698 0.135,0.198 10 false 8 3.094,0.469 3.229,0.667 0.135,0.198 10 false 9 3.01,1.542 3.25,1.74 0.24,0.198 10 false 10 1.74,0.396 1.875,0.594 0.135,0.198 10 true 1 1.74,1.615 1.875,1.813 0.135,0.198 10 true 2 1.042,0.417 1.177,0.615 0.135,0.198 10 true 3 1.031,1.615 1.167,1.813 0.135,0.198 10 true 4

Uniformly install and tighten the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



e.

Step 2:

i.

Tighten the 10 crankshaft bearing cap bolts again in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

If a crankshaft bearing cap bolt does not meet the specified torque, replace it.



f.

Step 3:

i.
A132155C09
2.25,0.138 2.406,0.285 0.156,0.148 10 *a 1.998,0.722 2.226,0.226 false 1.003,0.404 1.381,0.602 0.378,0.198 10 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the crankshaft bearing cap bolts with paint.


ii.

Tighten the crankshaft bearing cap bolts by 90° in the order shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 13041 10.INSTALL CONNECTING ROD BEARING

a.
A195818C13
0.406,3.073 0.521,3.073 0.521,3.073 0.74,3.448 false 1.729,3.667 1.938,3.896 0.208,0.229 10 false A 2.854,3.656 3.063,3.885 0.208,0.229 10 false B 0.24,2.979 0.417,3.135 0.177,0.156 10 false *a
*a Vernier Caliper


Clean the connecting rod bearing contact surface of the connecting rod sub-assembly and connecting rod cap, and both surfaces of both connecting rod bearings.


b.

Install the connecting rod bearings to the connecting rod sub-assemblies and connecting rod caps.


c.

Using a vernier caliper, measure the distance between the edges of the connecting rod sub-assembly and connecting rod bearing, and the edges of the connecting rod bearing cap and connecting rod bearing.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the connecting rod bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the connecting rod bearing inner surface.

·

If any coolant comes into contact with the connecting rod bearing inner surface, replace the connecting rod bearing with a new one.




Hide 11.INSTALL PISTON WITH CONNECTING ROD

a.
A289832C12
0.49,1.885 0.833,1.885 0.833,1.885 1.26,1.573 false 2.104,0.167 2.302,0.167 2.302,0.167 2.365,0.469 false 0.302,1.781 0.646,2.052 0.344,0.271 10 *a 1.948,0.073 2.375,0.448 0.427,0.375 10 *b 2.76,0.604 3.188,0.979 0.427,0.375 10 45°
*1 No. 1 Compression Ring and Oil Ring
*2 No. 2 Compression Ring and Oil Ring Expander
V100136

Engine Front


Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.

Position the piston rings so that the ring ends are as shown in the illustration.


c.
A195820C09
1.688,1.406 1.542,1.406 1.542,1.406 1.135,1.031 true 1.75,1.333 1.927,1.51 0.177,0.177 10 false *a
*a Front Mark


Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing the engine front.

NOTICE:

When inserting the piston with connecting rod into the cylinder block sub-assembly, make sure the oil nozzle does not interfere with the connecting rod sub-assembly.


HINT:

The front mark is "1L" printed in raised letters.



d.
A259172C10
0.535,0.319 0.731,0.501 0.196,0.182 10 *a 1.459,0.904 0.876,0.42 0.876,0.42 0.737,0.42 false
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.

NOTICE:

Match the connecting rod cap with the connecting rod sub-assembly.



e.
A259170

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


f.

Temporarily install the 2 connecting rod bolts.

HINT:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.

Alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.
A101478C51
2.063,0.729 2.375,0.531 false 1.083,0.323 1.438,0.5 0.354,0.177 10 false 90° 2.417,0.375 2.625,0.552 0.208,0.177 10 false *a
*a Paint Mark
V100136

Engine Front


Step 2:

i.

Mark the front of the 2 connecting rod bolts with paint.


ii.

Tighten the connecting rod bolts by 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.