Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR OUTSIDE MOULDING
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109646 REAR DOOR OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75797 1.INSTALL REAR DOOR UPPER OUTSIDE MOULDING PAD

a.

Clean the rear door outside moulding.

i.

Remove any double-sided tape from the rear door outside moulding.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear door upper outside moulding pad.

i.

Remove the release paper from the new rear door upper outside moulding pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



ii.

Install the rear door upper outside moulding pad as shown in the illustration.

B361240
0.938,0.615 1.167,0.365 1.167,0.365 0.823,0.615 false 6.646,0.635 6.115,0.365 6.115,0.365 6.25,0.635 false 1.219,0.271 1.396,0.458 0.177,0.188 10 false *a 5.938,0.281 6.104,0.479 0.167,0.198 10 false *a
*a Marking - -




Hide 2.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When installing the rear door outside moulding sub-assembly, heat the vehicle body and rear door outside moulding sub-assembly using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Outside Moulding Sub-assembly 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door outside moulding sub-assembly excessively.


a.

Install 8 new clips.


b.

Install a new gasket.


c.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



d.

Install the rear door outside moulding sub-assembly.

i.

Using a heat light, heat the vehicle body and rear door outside moulding sub-assembly.


ii.

Remove the release paper from the rear door outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 8 clips and attach the double-sided tape.

HINT:

Press the rear door outside moulding sub-assembly firmly to temporarily install it.



iv.

Install the nut.


v.

Install the hole plug.


vi.
B364577

Engage the 4 clips to install the rear door outside moulding sub-assembly.



Hide 75078 3.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When installing the rear door lower outside moulding sub-assembly, heat the vehicle body and rear door lower outside moulding sub-assembly using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Lower Outside Moulding Sub-assembly 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door lower outside moulding sub-assembly excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear door lower outside moulding sub-assembly.

i.

Using a heat light, heat the vehicle body and rear door lower outside moulding sub-assembly.


ii.

Remove the release paper from the new rear door lower outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 5 clips and attach the double-sided tape.

HINT:

Press the rear door lower outside moulding sub-assembly firmly to temporarily install it.



iv.
B362546

Engage the clip.


v.

Install the 2 clips.


vi.

Install the rear door lower outside moulding sub-assembly with the screw.