Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING(for Front Side)
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109648 WHEEL OPENING MOULDING(for Front Side) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75793 1.INSTALL FRONT DOOR UPPER OUTSIDE MOULDING PAD

a.

Clean the front fender moulding.

i.

Remove any double-sided tape from the front fender moulding.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door upper outside moulding pad.

i.

Remove the release paper from a new front door upper outside moulding pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



ii.
B363150
0.552,1 0.427,0.802 0.427,0.802 0.75,1 true 2.646,0.958 3.01,0.792 3.01,0.792 2.969,0.938 true 0.26,0.708 0.573,0.865 0.313,0.156 10 false *a 3.031,0.708 3.344,0.865 0.313,0.156 10 false *a
*a Marking


Install the front door upper outside moulding pad as shown in the illustration.



Hide 75086 2.INSTALL FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY

HINT:

When installing the front fender wheel opening moulding sub-assembly, heat the vehicle body and front fender wheel opening moulding sub-assembly using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Fender Wheel Opening Moulding Sub-assembly 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or front fender wheel opening moulding sub-assembly excessively.


a.

Engage the 2 claws to install the front fender moulding sub-assembly.


b.

Clean the vehicle body surface.

i.

Remove any double-sided tape from the vehicle body.


ii.

Wipe off any tape adhesive residue with cleaner.



c.

Remove the release paper from a new front fender wheel opening moulding sub-assembly and the front door upper outside moulding pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the 8 clips and attach the double-sided tape.

HINT:

Press the front fender wheel opening moulding sub-assembly with front fender moulding sub-assembly firmly to install it.



e.
B361055

Engage the 4 claws.


f.

w/o Mudguard:

i.

Install the 6 clips.


ii.

Install the 2 screws.



g.

w/ Mudguard:

i.

Install the 5 clips.



h.
B361059
2.604,1.427 2.896,1.427 true 2.917,1.344 3.146,1.521 0.229,0.177 10 true *1 0.448,1.875 0.76,2.031 0.313,0.156 10 false *a 1.146,1.896 1.458,2.052 0.313,0.156 10 false *b
*1 Pin Hold Clip
*a Correct
*b Incorrect


Install the clip.


i.

Install the front fender wheel opening moulding sub-assembly with the 2 screws.


j.

Install the pin hold clip as shown in the illustration.

NOTICE:

Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.



Hide 76622C 3.INSTALL FRONT FENDER MUDGUARD (w/ Mudguard)