Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING(for Rear Side)
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109649 WHEEL OPENING MOULDING(for Rear Side) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear Side)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 76626D 1.REMOVE REAR QUARTER PANEL MUDGUARD (w/ Mudguard)

Hide 75874 2.REMOVE QUARTER PANEL WHEEL OPENING MOULDING

a.
B404756

w/o Mudguard:

i.

Remove the 3 screws.


ii.

Remove the 4 clips.



b.
B408551

w/ Mudguard:

i.

Remove the 2 screws.


ii.

Remove the 4 clips.



c.

While pulling the rear bumper assembly, insert a finger between the rear bumper side seal LH and rear bumper assembly and disengage the 4 claws by pushing the area shown in the illustration.

B408132C01
0.927,2.969 1.281,2.792 false 1.708,2.531 1.813,2.719 false 1.417,2.385 1.771,2.208 false 3.271,2.375 3.625,2.198 false 5.021,2.385 5.375,2.208 false 3.146,2.896 3.479,3.115 false 2.813,3.406 3.167,3.229 false 4.906,3.01 5.229,3.021 false 4.594,3.479 4.948,3.521 false 0.76,2.927 1.073,3.083 0.313,0.156 10 false *1 1.552,2.438 1.865,2.594 0.313,0.156 10 false *2 1.833,2.115 2.146,2.271 0.313,0.156 10 false *3 3.594,2.656 3.906,2.813 0.313,0.156 10 false *a 2.188,1.146 2.344,1.344 0.156,0.198 10 true 1 2.177,0.917 2.333,1.115 0.156,0.198 10 true 2 2.167,0.708 2.323,0.906 0.156,0.198 10 true 3 2.094,0.5 2.25,0.698 0.156,0.198 10 true 4 3.688,2.125 4,2.281 0.313,0.156 10 false *3 5.427,2.125 5.74,2.281 0.313,0.156 10 false *3 2.979,2.792 3.292,2.948 0.313,0.156 10 false *2 2.625,3.344 2.938,3.5 0.313,0.156 10 false *1 4.708,2.938 5.021,3.094 0.313,0.156 10 false *2 4.417,3.385 4.729,3.542 0.313,0.156 10 false *1
*1 Quarter Panel Wheel Opening Moulding *2 Rear Bumper Assembly
*3 Rear Bumper Side Seal - -
*a Push - -


NOTICE:

To avoid damaging the claws, do not forcibly pull the quarter panel wheel opening moulding.


HINT:

Disengage the claws in the order shown in the illustration.



d.

Disengage the 4 clips to remove the quarter panel wheel opening moulding.