Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Front Door)
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109653 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

NOTICE:

Do not heat the vehicle body excessively.



ii.

Clean off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape becomes stiff and comes off easily. When the temperature is high, the tape elasticity increases.





c.

Before installation

i.

Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for installation of the tape (How to use a squeegee and installation procedure for flat surfaces)

NOTICE:
·

Position the tape accurately to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B200106C10
0.104,0.115 3.417,1.615 3.313,1.5 2.344,0.281 2.281,0.281 2.281,0.281 2.135,0.74 false 1.417,1.156 1.417,1.344 false 0.833,0.49 0.677,0.615 false 1.865,3.521 2.01,3.521 false 5.427,3.458 5.573,3.458 false 1.531,3.094 1.688,3.229 false 4.781,3.125 5.177,3.198 false 0.167,0.156 0.396,0.417 0.229,0.26 10 *a 2.396,0.208 2.729,0.49 0.333,0.281 10 *b 1.344,1.354 1.542,1.594 0.198,0.24 10 *c 0.875,0.396 1.135,0.646 0.26,0.25 10 *d 0.083,1.708 0.365,1.979 0.281,0.271 12 *A 3.948,1.698 4.292,1.958 0.344,0.26 12 *B 2.063,1.823 2.24,2.052 0.177,0.229 10 C 5.417,2.583 5.646,2.833 0.229,0.25 10 D 1.688,3.427 1.875,3.677 0.188,0.25 10 *e 5.26,3.375 5.479,3.604 0.219,0.229 10 *e 1.375,3 1.563,3.281 0.188,0.281 10 *1 1.115,2.385 1.385,2.646 0.271,0.26 10 B 4.583,2.365 4.844,2.646 0.26,0.281 10 B 2.813,2.573 2.969,2.771 0.156,0.198 10 A 6.292,2.229 6.438,2.479 0.146,0.25 10 A 4.615,3.031 4.802,3.26 0.188,0.229 10 *1
*A Pressing Forward *B Pulling
*1 Black Out Tape - -
*a Side View *b Non-padded Side
*c Padded Side *d Squeegee
*e Release Paper - -


Reference Measurement:
Area Measurement Area Measurement
A 10 to 20 mm (0.394 to 0.787 in.) B 30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
C 40 to 50° (for pressing forward) D 30 to 45° (for pulling)


NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.





f.

Key points for installation of the tape (How to use a squeegee and installation procedure for hemmed surfaces)

i.
B147253C13
1.188,0.708 0.844,0.25 false 0.844,1 1.115,1.271 0.271,0.271 10 *e 1.396,0.521 1.656,0.771 0.26,0.25 10 *d 2.01,0.479 2.26,0.76 0.25,0.281 10 *c 0.677,0.146 0.938,0.396 0.26,0.25 10 *a 1.552,1.823 1.896,2.083 0.344,0.26 10 *b
*a Squeegee
*b Hem
*c First
*d Second
*e Third


If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for installation of the tape (How to use a squeegee and installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.



h.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

NOTICE:

Do not reuse the tape.




Hide 75969 2.INSTALL FRONT DOOR REAR INNER BLACK OUT TAPE

a.

Refer to the illustration to position a new front door rear inner black out tape.

B363139C01
5.365,0.594 5.646,0.792 false 5.26,1.677 5.5,1.552 false 4.781,2.365 4.927,2.583 false 6.292,2.354 6.156,2.573 false 4.375,2.177 4.75,2.427 0.375,0.25 12 false *A 5.604,2.167 5.938,2.427 0.333,0.26 12 false *B 5.208,0.521 5.521,0.677 0.313,0.156 10 false *a 4.625,2.281 4.938,2.438 0.313,0.156 10 false *b 6.323,2.271 6.635,2.427 0.313,0.156 10 false *c 5.104,1.604 5.417,1.76 0.313,0.156 10 false *a 5.594,0.219 5.75,0.417 0.156,0.198 10 false A 5.5,1.906 5.656,2.104 0.156,0.198 10 false B 0.76,2.469 0.917,2.667 0.156,0.198 10 false a 1.125,2.375 1.281,2.573 0.156,0.198 10 false a 3.5,0.094 3.729,0.302 0.229,0.208 10 false a-a
*A LH Side *B RH Side
*a Edge of Curved Surface *b Square
*c Round - -


Standard Measurement:
Area Measurement Area Measurement
A 1.5 mm (0.0591 in.) B 1.0 mm (0.0394 in.)



b.

Remove the release paper and apply the front door rear inner black out tape.


Hide 75939 3.INSTALL FRONT DOOR UPPER INNER BLACK OUT TAPE

a.

Refer to the illustration to position a new front door upper inner black out tape.

B363138C01
4.979,2.698 4.979,2.448 false 5.677,3.479 5.677,3.229 false 4.854,0.917 5.063,1.188 false 5.781,1.073 6.031,0.844 false 4.333,2.729 4.677,2.969 0.344,0.24 12 false *A 4.333,1.938 4.688,2.167 0.354,0.229 12 false *B 4.688,0.854 5,1.01 0.313,0.156 10 false *a 5.615,3.5 5.927,3.656 0.313,0.156 10 false *b 4.917,2.708 5.229,2.865 0.313,0.156 10 false *c 6.063,0.76 6.375,0.917 0.313,0.156 10 false *a 2.563,1.99 2.719,2.188 0.156,0.198 10 false a 2.427,2.24 2.583,2.438 0.156,0.198 10 false a 4.365,0.052 4.823,0.25 0.458,0.198 10 false a-a 4.188,1.083 4.344,1.281 0.156,0.198 10 false A 6.5,1.146 6.656,1.344 0.156,0.198 10 false B
*A LH Side *B RH Side
*a Edge of Curved Surface *b Square
*c Round - -


Standard Measurement:
Area Measurement Area Measurement
A 1.5 mm (0.0591 in.) B 1.0 mm (0.0394 in.)



b.

Remove the release paper and apply the front door upper inner black out tape.


Hide 67663D 4.INSTALL DOOR FRAME GARNISH

Hide 68151D 6.INSTALL FRONT DOOR GLASS RUN

Hide 68102 7.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 8.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67602 9.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 81230N 10.INSTALL COURTESY LIGHT ASSEMBLY

Hide 11.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 12.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 69284C 13.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 67492A 14.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 16.INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 17.INSPECT POWER WINDOW OPERATION