Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0109807 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and store this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to TCM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed more than 20 km/h (12.43 mph)
(b) Engine speed more than 1000 rpm
(c) STA signal ON
·

Park/neutral position switch assembly

·

Starter relay circuit

·

Cranking holding function circuit

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C301517
6.146,1.188 6.604,1.385 0.458,0.198 10 false STA 6.146,1.646 6.604,1.844 0.458,0.198 10 false NSW 5.813,1.177 6.271,1.375 0.458,0.198 10 false A43 5.885,0.979 6.042,1.177 0.156,0.198 10 false 9 5.844,1.458 6.156,1.656 0.313,0.198 10 false 65 5.844,1.635 6.156,1.833 0.313,0.198 10 false C1 6.323,2.323 6.781,2.521 0.458,0.198 10 false ECM 6.156,2.969 6.615,3.167 0.458,0.198 10 false NSW 5.833,2.958 6.146,3.156 0.313,0.198 10 false C3 5.844,2.771 6.156,2.969 0.313,0.198 10 false 11 5.833,4.198 6.146,4.396 0.313,0.198 10 false C3 5.833,4 6.146,4.198 0.313,0.198 10 false 10 6.146,4.188 6.604,4.385 0.458,0.198 10 false STA 6.156,4.563 6.469,4.76 0.313,0.198 10 false E1 5.833,4.563 6.146,4.76 0.313,0.198 10 false C3 5.885,4.385 6.042,4.583 0.156,0.198 10 false 8 3.854,1.656 5.219,2.063 1.365,0.406 10 false to Certification ECU*1 4.594,2.76 4.75,2.958 0.156,0.198 10 false P 4.792,2.76 4.948,2.958 0.156,0.198 10 false N 4.99,2.865 5.146,3.063 0.156,0.198 10 false 4 4.396,2.948 4.552,3.146 0.156,0.198 10 false B 4.406,3.146 4.563,3.344 0.156,0.198 10 false L 4.208,3.042 4.396,3.344 0.188,0.302 10 false 9 4.094,3.542 5.417,4.219 1.323,0.677 10 false Park/Neutral Position Switch Assembly 4.083,3.375 4.542,3.573 0.458,0.198 10 false C14 6.375,4.969 6.833,5.167 0.458,0.198 10 false TCM 3.854,1.927 4.958,2.479 1.104,0.552 10 false to Ignition Switch Assembly*2 0.49,1.656 1.583,1.927 1.094,0.271 10 false from Battery*1 0.49,1.958 1.719,2.448 1.229,0.49 10 false from Ignition Switch Assembly*2 2.052,2.625 2.208,2.823 0.156,0.198 10 false 3 2.615,2.625 2.771,2.823 0.156,0.198 10 false 5 2.615,3.052 2.771,3.25 0.156,0.198 10 false 2 2.042,3.052 2.198,3.25 0.156,0.198 10 false 1 2.292,3.396 2.604,3.594 0.313,0.198 10 false ST 0.906,2.708 1.948,2.927 1.042,0.219 10 false to Starter 0.052,5.323 1.823,5.625 1.771,0.302 10 false *2: w/o Smart Key System 0.052,5.063 1.833,5.573 1.781,0.51 10 false *1: w/ Smart Key System

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE

·

Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the airfuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal Open or Close Open: Starter operating
Close: Starter not operating
-
Powertrain > ECT > Data List
Tester Display
Starter Signal
50003 235 193

e.

Crank the engine.


f.

Read the value displayed on the GTS.

OK:
Tester Display Condition Specified Condition
Starter Signal Ignition switch ON Close
Starter Signal Engine is cranking Open



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
A107908
0.344,1.542 0.771,1.823 0.427,0.281 1.219,1.552 0.781,1.063 false 0.792,2.646 1.281,2 false 1.969,1.552 2.542,1.021 false 0.24,0.219 0.469,0.406 0.229,0.188 10 false *a 0.667,0.917 0.885,1.094 0.219,0.177 10 false B 0.708,2.656 0.917,2.833 0.208,0.177 10 false L 2.573,0.906 2.885,1.083 0.313,0.177 10 false RB 0.458,1.594 0.875,1.854 0.417,0.26 10 false C14
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-4 (B) - C14-9 (L) Shift lever in P Below 1 Ω
Shift lever in N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
C14-1 (RB) - C14-9 (L) Shift lever in P 10 kΩ or higher
Shift lever in R 10 kΩ or higher
Shift lever in N 10 kΩ or higher
Shift lever in D 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TCM - PARK/NEUTRAL POSITION SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (TCM - PARK/NEUTRAL POSITION SWITCH)
a.
C189544
1.563,0.875 2.052,1.177 0.49,0.302 1.479,2.25 0.896,2.979 false 0.24,0.271 0.458,0.51 0.219,0.24 10 false *a 1.729,0.938 2.042,1.094 0.313,0.156 10 false C3 0.698,3 1.135,3.156 0.438,0.156 10 false STA
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-10 (STA) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 235

e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / ECT/ Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

g.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output OK
DTC P0617 is output NG




OK

END

NG