Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0109808 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensors detect the wheel speed and send the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of these pulse signals.

C298117
2.677,0.385 3.75,0.583 1.073,0.198 10 false 4-Pulse 4.708,0.49 5.781,0.688 1.073,0.198 10 false 4-Pulse 5.76,1.26 6.833,1.458 1.073,0.198 10 false TCM 1.615,1.021 2.302,1.781 0.688,0.76 10 false Skid Control ECU 3.469,1.417 4.333,1.948 0.865,0.531 10 false Combination Meter 0.229,1.167 1.135,2.073 0.906,0.906 10 false from Speed Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" When the ECT sensor is normal and the counter gear speed is 300 rpm or more, the vehicle speed signal is not input for 2 seconds or more.
·

Open or short in vehicle speed signal circuit

·

Combination meter

·

Vehicle speed sensor (Brake control system)

·

Skid control ECU (Brake control system)

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the transmission counter gear indicates more than 300 rpm and over 30 seconds have passed since the park/neutral position switch assembly was turned off. If there is no vehicle speed signal with these conditions satisfied, the TCM concludes that there is a vehicle speed signal malfunction. The TCM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

When a DTC P0500 is output, a ground short in the wiring of terminal SPD or an internal ground short in the relevant ECU is suspected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit

PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described for a speedometer malfunction.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / ECT / Data List / Vehicle Speed.

Powertrain > ECT > Data List
Tester Display
Vehicle Speed
50003 235 316

f.

Drive the vehicle.


g.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.

Inspect the combination meter assembly using an oscilloscope.

C275469
3.323,0.219 3.74,0.469 0.417,0.25 4.333,1.875 3.927,1.281 false 4.49,3.781 4.948,3.979 0.458,0.198 10 false GND 3.417,0.26 3.875,0.458 0.458,0.198 10 false F22 4.313,1.906 4.771,2.104 0.458,0.198 10 false +S 0.573,0.271 1.031,0.469 0.458,0.198 10 false *a
*a Component with harness connected
(Combination Meter Assembly)
- -


i.

Move the shift lever to N.


ii.

Jack up the vehicle.


iii.

Turn the ignition switch to ON.


iv.

Measure the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.

Standard Voltage:
Tester Connection Condition Specified Condition
F22-3 (+S) - Body ground Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F22-3 (+S) - C3-3 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - TCM)