DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH) |
Actual vehicle speed | - |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383.75 rpm |
600 to 700 rpm: Idling | - |
| Calculate Load | Calculated load by ECM | Min.: 0.0%
Max.: 100.0% |
·
Ignition switch ON: 0.0% ·
Idling (engine warmed up): 23.5% ·
Running without load (3000 rpm): 22.3% ·
Vehicle driven at constant speed of 60 km/h (37 mph): 59.6% |
This is the engine load calculated based on the estimated intake pressure. Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%)
(For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Coolant Temp | Engine coolant temperature | Min.: -40 C (-40 F)
Max.: 140 C (284 F) |
75 to 100°C (167 to 212°F): After warming up | ·
If value -40°C (-40°F): sensor circuit open ·
If value 140°C (284°F): sensor circuit shorted |
| Intake Air | Intake air temperature | Min.: -40 C (-40 F)
Max.: 215 C (419 F) |
Equivalent to ambient air temperature | ·
If value -40°C(-40°F): sensor circuit open ·
If value 215°C(419°F): sensor circuit shorted |
| Engine Run Time | Engine run time | Min.: 0 S
Max.: 65535 S |
Time after engine start | - |
| Battery Voltage | Battery voltage | Min.: 0
Max.: 65.535 V |
11 to 14 V: Idling | - |
| Throttle Sensor Volt % | Throttle position sensor output | Min.: 0%
Max.: 100% |
10 to 22%: Idling | Calculated value based on VTA1 |
| Starter Signal | Starter signal | Open or Close | - | - |
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status | ON or OFF | Brake pedal is
·
ON: Depressed ·
OFF: Released |
- |
| TC Terminal | TC Terminal Status | ON or OFF | - | - |
| # Codes(Include History) | # of Codes | Min.: 0
Max.: 255 |
- | Number of detected DTCs |
| MIL ON Run Distance | MIL ON run distance | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL ON | Min.: 0 min.
Max.: 65535 min. |
Equivalent to running time after MIL ON | - |
| Time after DTC Cleared | Time after DTC cleared | Min.: 0 min.
Max.: 65535 min. |
Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Equivalent to time after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | Min.: 0
Max.: 255 |
- | Number of warm-up cycles after DTCs cleared |
| TC and TE1 | TC and TE1 terminals of DLC3 | ON or OFF | - | Active Test support data |
| Transmission Type2 | [NA] | - | - | - |
| Throttle Position from EFI | Throttle sensor position | Min.: 0.0%
Max.: 100.0% |
- | Recognition value for throttle opening angle on ECM |
| Accel Position from EFI | Absolute Accelerator Pedal Position | Min.: 0.0%
Max.: 100.0% |
- | - |
| SPD (NT) | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
Lock-up is
·
ON (After warming up the engine): Input turbine speed (NT) is equal to engine speed ·
OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed |
- |
| SPD (NC) | Counter gear speed | Min.: 0 rpm
Max.: 12750 rpm |
- | - |
| Shift SW Status (P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held "-" (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | ATF temp. sensor value | Min.: -40 C (-40 F)
Max.: 215 C (419 F) |
·
After stall test; Approx. 80°C (176°F) ·
Equal to ambient temperature when cold soak |
If the value is "-40°C (-40°F)" or "150°C (302°F)", ATF temp. sensor circuit is open or shorted. |
| NT Sensor Voltage | Input speed sensor NT output voltage | Min.: 0 V
Max.: 5.000 V |
0.1 to 1.9 V | - |
| NC Sensor Voltage | Output speed sensor NC output voltage | Min.: 0 V
Max.: 5.000 V |
0.1 to 1.9 V | - |
| TPS 3 Switch | ATF pressure switch No. 3 status | ON or OFF | ·
ON: Shift solenoid valve SLU is ON ·
OFF: Shift solenoid valve SLU is OFF |
- |
| Lock Up | Lock up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | TCM gear shift command | 1st, 2nd, 3rd, 4th, 5th or 6th | Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid SLT status | ON or OFF | ·
ON: Shift solenoid SLT operating ·
OFF: Shift solenoid SLT not operating |
- |
| SLU Solenoid Status | Shift Solenoid SLU Status | ON or OFF | ·
ON: Shift solenoid SLU operating ·
OFF: Shift solenoid SLU not operating |
- |
| SL Solenoid Status | Shift Solenoid SL Status | ON or OFF | ·
ON: Shift solenoid SL operating ·
OFF: Shift solenoid SL not operating |
- |
*: Refer to DTC P0705.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P0705
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Connects and disconnects TC and TE1.
(changes to the fluid temperature detection mode) |
ON/OFF | The MIL will not blink when "Connect the TC and TE1 / ON" is selected. |
| Activate the Solenoid (SLU) | Operates shift solenoid SLU | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SLT) | Operates shift solenoid SLT to raise the line pressure. | ON/OFF
|
[Vehicle Condition]
·
Vehicle Stopped ·
IDL: ON |
| Activate the Lock Up | Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. | ON/OFF | Can be used to check SLU and SL solenoid operation.
[Vehicle Condition] ·
Throttle valve opening angle: Less than 20% ·
Vehicle speed:60 km/h (37 mph) or more, and 6th gear |
| Activate the Solenoid (SL) | Operates shift solenoid SL | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to be selected manually. | ·
Press "→" button: Upshift occurs ·
Press "←" button: Downshift occurs |
Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (31 mph) or less |
| Activate the Solenoid (SL1) | Operates shift solenoid SL1 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operates shift solenoid SL2 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL3) | Operates shift solenoid SL3 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL4) | Operates shift solenoid SL4 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST
Note that the pressure readings for the Active Test and Hydraulic Test are different.