Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0109808 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0791  Intermediate Shaft Speed Sensor "A" Circuit  P0793  Intermediate Shaft Speed Sensor "A"  


DESCRIPTION

This sensor detects the rotation speed of the counter gear, which indicates the intermediate shaft revolution (speed) of the transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C133216
3.146,1.729 2.458,0.542 2.458,0.542 2.24,0.542 false 4.083,1.688 4.458,0.51 4.458,0.51 4.594,0.51 false 3.688,2.698 4,3.271 4,3.271 4.125,3.271 false 3.104,2.49 2.75,3.323 2.75,3.323 2.646,3.323 false 2.052,0.469 2.302,0.646 0.25,0.177 10 *1 4.625,0.427 4.781,0.594 0.156,0.167 10 *2 2.479,3.26 2.646,3.406 0.167,0.146 10 *3 4.156,3.208 4.333,3.354 0.177,0.146 10 *4
*1 Counter Gear *2 Clutch Drum
*3 Output Speed Sensor NC *4 Input Speed Sensor NT


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0791 Intermediate Shaft Speed Sensor "A" Circuit When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 2 seconds or more. (1-trip detection logic)
·

Transmission revolution sensor (speed sensor NC)

·

Transmission wire

·

TCM


Comes on DTC stored
P0793 Intermediate Shaft Speed Sensor "A" When the vehicle speed is 25 km/h (15.5 mph) or higher, the counter gear speed is less than 300 rpm for 2 seconds or more. (1-trip detection logic)
·

Transmission revolution sensor (speed sensor NC)

·

Transmission wire

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates gear shifts comparing the speed sensor (NT) with the speed sensor (NC).

While the vehicle is being driven in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 and the output shaft revolution (speed) is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores a DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C133260
5.083,2.24 5.625,2.417 0.542,0.177 10 NCB 5.083,2.719 5.625,2.896 0.542,0.177 10 NCO 5.594,4.5 6.188,4.708 0.594,0.208 10 TCM 0.76,3.521 2.49,3.698 1.729,0.177 10 (Output Speed Sensor NC) 2.021,3.896 3.344,4.25 1.323,0.354 10 Transaxle Assembly 0.688,3.281 2.74,3.458 2.052,0.177 10 Transmission Revolution Sensor

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NC) Counter gear speed Min.: 0 rpm, Max.: 12750 rpm - Data is displayed in increments of 50 rpm
Powertrain > ECT > Data List
Tester Display
SPD (NC)
50003 235 142
HINT:
·

SPD (NC) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
a.

Remove the valve body assembly.


b.
C133219

Make sure that the connector is properly connected, and check the speed sensor installation.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>INSTALLATION

OK:

The installation bolts are tightened properly and there is no clearance between the sensor and valve body assembly.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION WIRE

NG

REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR

2.INSPECT TRANSMISSION WIRE
a.

Remove the TCM.

C275470
3.365,2.542 3.531,1.531 false 4.146,2.521 3.656,1.51 false 3.115,4.313 3.708,3.875 false 4.021,4.313 3.99,3.854 false 0.885,0.427 1.198,0.625 0.313,0.198 10 *a 2.01,1.25 2.323,1.448 0.313,0.198 10 *b 2.125,3.198 2.438,3.396 0.313,0.198 10 *c 3.198,2.615 3.813,2.958 0.615,0.344 10 NCB 4.063,2.594 4.677,2.938 0.615,0.344 10 NCO 2.938,4.354 3.552,4.698 0.615,0.344 10 NCO 3.938,4.354 4.552,4.698 0.615,0.344 10 NCB
*a Component without harness connected
(Transmission Wire)
*b TCM side
*c Sensor side - -



b.

Disconnect the speed sensor connector from the transmission wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (NCO) sensor side - 3 (NCO) TCM side Always Below 1 Ω
4 (NCB) sensor side - 4 (NCB) TCM side Always Below 1 Ω
3 (NCO) sensor side - Body ground and other terminals Always 10 kΩ or higher
4 (NCB) sensor side - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE TRANSMISSION REVOLUTION SENSOR

NG

3.REPLACE TRANSMISSION REVOLUTION SENSOR

NEXT

4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0791 AND/OR P0793 IS OUTPUT AGAIN)
4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0791 AND/OR P0793 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > ECT > Clear DTCs
50002 235


e.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P0791 or P0793 is output A
DTCs are not output B




A

B

END