Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0109808 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0989  Transmission Fluid Pressure Sensor / Switch "E" Circuit Low  P0990  Transmission Fluid Pressure Sensor / Switch "E" Circuit High  


DESCRIPTION

ATF pressure switch No. 3 is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0989 Transmission Fluid Pressure Sensor / Switch "E" Circuit Low Transmission fluid pressure switch No. 3 is OFF when lock-up occurs in response to a lock-up request (2 trip detection logic).
·

ATF temperature sensor assembly (ATF pressure switch No. 3)

·

Transmission wire

·

TCM


Comes on DTC stored
P0990 Transmission Fluid Pressure Sensor / Switch "E" Circuit High When both of the following conditions are detected (2 trip detection logic):
·

Transmission fluid pressure switch No. 3 is ON when lock-up does not occur.

·

Lock-up does not occur when shift solenoid valve (SLU) is requested to turn off in the lock-up range.


·

ATF temperature sensor assembly (ATF pressure switch No. 3)

·

Transmission wire

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM illuminates the MIL and stores the DTC if it detects that the ATF pressure switch is OFF with the lock-up solenoid ON or if it detects that the ATF pressure switch is ON with the lock-up solenoid OFF.

WIRING DIAGRAM

C133258
5.098,1.884 5.644,2.052 0.545,0.168 10 TPS3 5.553,4.582 6.293,4.743 0.74,0.161 10 TCM 0.928,3.166 2.983,3.583 2.055,0.417 10 ATF Pressure Switch No. 3 1.699,3.823 3.754,4.255 2.055,0.432 10 Transaxle Assembly

PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0989 OR P0990)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P0990 is output A
Only DTC P0989 is output B
P0989 or P0990 and other DTCs are output C


HINT:

If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be stored.




A

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)

B

4.CHECK TRANSMISSION WIRE

C

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)
a.
C133212
1.781,1.031 2.323,0.875 false 2.365,0.781 2.74,0.938 0.375,0.156 10 TPS3 0.635,0.302 1.01,0.458 0.375,0.156 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the TCM.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
19 (TPS3) - Body ground (Valve body assembly) and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 3)
3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 3)
a.

Remove the oil strainer assembly.


b.
C142709
1.559,1.138 2.081,2.028 false 1.955,2.042 2.343,2.189 0.388,0.147 10 TPS3

Disconnect the connector from the ATF temperature sensor assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (TPS3) - Body ground (Valve body assembly) and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.CHECK TRANSMISSION WIRE
a.

Remove the oil strainer assembly.


b.
C175651
2.458,4.125 2.156,3.771 false 2.198,2.135 1.948,1.74 false 0.76,0.625 0.958,0.844 0.198,0.219 10 *b 2.323,4.177 2.792,4.333 0.469,0.156 10 TPS3 0.76,2.969 0.958,3.188 0.198,0.219 10 *c 2.052,2.167 2.542,2.323 0.49,0.156 10 TPS3 0.156,0.115 0.354,0.333 0.198,0.219 10 *a
*a Component without harness connected
(Transmission Wire))
*b TCM Side
*c ATF Temperature Sensor Side


Remove the TCM.


c.

Disconnect the connector from the ATF temperature sensor assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
19 (TPS3) TCM side - 1 (TPS3) sensor side Always Below 1 Ω
1 (TPS3) sensor side - Body ground (Valve body assembly) and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

NG

5.REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

NEXT

6.CHECK IF DTC OUTPUT RECURS
6.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 235
HINT:

Write down the currently output DTCs before clearing them.




e.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P0989 is output A
DTCs are not output B




A

B

END