Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM J

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S and it is moved toward "-" or "+", it is possible to select different shift ranges (1st through 6th ranges).

Moving the shift lever toward "+" increases the shift range by one, and moving the shift lever toward "-" decreases the shift range by one.

WIRING DIAGRAM

C301471E01
5.406,1.385 6.021,1.583 0.615,0.198 10 false SFTU 2.802,1.292 3.417,1.49 0.615,0.198 10 false SFTU 5.406,1.99 6.021,2.188 0.615,0.198 10 false SFTD 2.802,1.885 3.417,2.083 0.615,0.198 10 false SFTD 3.042,2.458 3.198,2.656 0.156,0.198 10 false S 5.396,2.573 5.552,2.771 0.156,0.198 10 false S 1.5,3.198 3.667,3.813 2.167,0.615 10 false Transmission Floor Shift Assembly (Transmission Control Switch) 1.51,3.021 1.969,3.219 0.458,0.198 10 false F46 5.531,3.542 5.99,3.74 0.458,0.198 10 false A43 5.521,3.74 5.979,3.938 0.458,0.198 10 false ECM 0.417,2.521 0.979,3.25 0.563,0.729 10 false from IG1 NO.3 fuse 5.135,1.292 5.448,1.49 0.313,0.198 10 false 42 5.146,1.885 5.458,2.083 0.313,0.198 10 false 43 5.146,2.458 5.458,2.656 0.313,0.198 10 false 27 3.24,1.292 3.396,1.49 0.156,0.198 10 false 2 3.24,1.875 3.396,2.073 0.156,0.198 10 false 1 3.24,2.458 3.396,2.656 0.156,0.198 10 false 7 1.885,1.292 2.042,1.49 0.156,0.198 10 false E 1.896,2.458 2.208,2.656 0.313,0.198 10 false IG 1.708,1.292 1.865,1.49 0.156,0.198 10 false 5 1.708,2.458 1.865,2.656 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held "-" (down-shift)


-
Powertrain > Engine > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 234 134,135
Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B




A

2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C168574C13
0.406,1.375 0.896,1.646 0.49,0.271 1.844,2.094 2.427,1.729 false 0.135,0.229 0.479,0.563 0.344,0.333 10 false *a 2.531,1.635 2.844,1.833 0.313,0.198 10 false IG 0.531,1.438 1.031,1.698 0.5,0.26 10 false F46
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector from transmission floor shift assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

CHECK POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C168574C13
0.406,1.375 0.896,1.646 0.49,0.271 1.844,2.094 2.427,1.729 false 0.135,0.229 0.479,0.563 0.344,0.333 10 false *a 2.531,1.635 2.844,1.833 0.313,0.198 10 false IG 0.531,1.438 1.031,1.698 0.5,0.26 10 false F46
*a Front view of wire harness connector
(to Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C168599C01
1.646,1.854 1.438,1.323 true 1.25,2.521 1.667,2.104 true 1.875,1.833 2.042,1.333 true 2.031,1.885 2.438,1.656 true 2.313,2.458 2.031,2.104 true 0.208,0.198 0.583,0.49 0.375,0.292 10 false *a 1.25,1.135 1.563,1.333 0.313,0.198 10 false IG 1.021,2.5 1.333,2.698 0.313,0.198 10 false S 1.885,1.094 2.427,1.344 0.542,0.25 10 false SFTU 2.427,1.458 2.969,1.708 0.542,0.25 10 false SFTD 2.438,2.396 2.75,2.594 0.313,0.198 10 false E
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-3 (IG) - F46-7 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
F46-2 (SFTU) - F46-5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
F46-1 (SFTD) - F46-5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Connect the transmission control switch connector.


b.
C233487C12
1.479,0.229 1.969,0.521 0.49,0.292 2.083,1.25 1.969,1.823 1.969,1.823 1.76,1.823 false 2.156,1.25 2.281,1.823 2.281,1.823 2.49,1.823 false 2.083,1.177 2.188,0.51 2.188,0.51 2.615,0.51 false 0.167,0.094 0.469,0.354 0.302,0.26 10 false *a 1.625,0.292 2.042,0.51 0.417,0.219 10 false A43 1.271,1.75 1.656,1.906 0.385,0.156 10 false SFTU 2.521,1.74 2.906,1.896 0.385,0.156 10 false SFTD 2.656,0.417 2.813,0.573 0.156,0.156 10 false S
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-27 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
A43-27 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-42 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
A43-43 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR